10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
Hi Forum.
I'm running the following awk command to extract the suffix value (pos 38) from the "AM00" record and append to the end of the "AM01" record.
awk 'substr($0,13,4)=="AM00" {SUFFIX = substr($0,38,2)} substr($0,13,4)=="AM01" {$0 = $0 SUFFIX} 1' before.txt > after.txt
Before.txt:... (2 Replies)
Discussion started by: pchang
2 Replies
2. Shell Programming and Scripting
Hello Gurus,
I am firing the below command :
df -g | grep -v var| awk '{ (if $4 > 90% ) print "Filesystem", $NF,"over sized";}'
But I am getting the below error:-
======
syntax error The source line is 1.
The error context is
{if ($4 > >>> 90%) <<<
awk: The... (9 Replies)
Discussion started by: pokhraj_d
9 Replies
3. Solaris
Hi Folks,
When i execute the command df -kh in my system the o/p hangs..
The command runs fine but takes a lot of time before coming back to the # prompt.
Can anyone please suggest the possible cause and solution?. (10 Replies)
Discussion started by: vivek.goel.piet
10 Replies
4. UNIX for Dummies Questions & Answers
Currently I am using the following sz and rz commands to run file transfer using ZMODEM within a perl script.
sz -b -m1 -M2 -k -e -r -u -t10
rz -b -m 1 -M 120 -y
Is there any flag setting that will allow me to terminate when a retry 0 error is outputted as this is constantly filling up my... (0 Replies)
Discussion started by: M1keSt4r
0 Replies
5. Shell Programming and Scripting
Hello,
I have a script that contains the command "whois 1.2.3.4"
Sometimes this command takes far too long to produce any output and as a result the rest of the script is not executed.
Can anyone suggest a method so that if no output is produced after say 2 seconds the script skips that... (2 Replies)
Discussion started by: colinireland
2 Replies
6. Shell Programming and Scripting
Org file
192.168.1.10 d:\adir\xdir
192.168.1.11 d:\bdir\ydir
want to covert it into
robocopy \\192.168.1.10\d$\adir\xdir\log* some_localdir\adir
robocopy \\192.168.1.10\d$\adir\ydir\log* some_localdir\bbdir (5 Replies)
Discussion started by: ydk
5 Replies
7. Shell Programming and Scripting
I have a problem with an awk command.
I have a expect script running on one node that is executing a command on another node.
Both nodes are Linux.
The script on the remote node is supposed to check a couple of logs after "type" notifications.
I am using tail and awk to do that.
The env... (6 Replies)
Discussion started by: unakon
6 Replies
8. SuSE
Hi,
Our systems:
system1: amd 64 running suse linux 9 enterprize
system2: amd 64 running esx vmware 3 with suse linux 9 enterprize.
The problem is:
when we ssh into system2 and execute the command:
ls -al
the session hangs. Infact session hangs when we execute any... (3 Replies)
Discussion started by: rajranibl
3 Replies
9. Shell Programming and Scripting
Hi,
I have a awk script to read a CSV file.
After reading the values i want to call a executable (nameely call_it) with the values what i read from the scv file.
I dont want to use system command inside the awk.
Is there any other way to run the executable from the awk script
Thanks ... (1 Reply)
Discussion started by: Raghuram.P
1 Replies
10. UNIX for Dummies Questions & Answers
Hi All,
I am unable to figure out why my ps command is haning.
Is some one else is running a process which is hanged. But in that case also if i do ps it should show only the processes running by me only.
Thanks & Regards
Gauri Agrawal (2 Replies)
Discussion started by: gauri
2 Replies