The message means that you are getting hardware errors. The bad hardware could be a CD, a CD drive, a cable, or an IDE controller. If you get a lot of these errors then it is likely that some piece of your hardware is about to fail permanently.
Another possibility is a very old and slow disc or a dirty or slightly corroded connector. Since
it is easy, cheap, and quick to try to fix up a possible connector problem, that's what I'd try first.
---------- Post updated at 12:12 PM ---------- Previous update was at 12:11 PM ----------
My first step would be to power down, and reseat the disc cables. I'd pull them back about 1/2
the way it would take to disengage the connectors, "rock" them back and forth a few times, then
reseat them fully back. I'd do the same with the power supply connectors to the discs. If you have
an older machine with a separate disc controller board, then I'd remove and reseat the controller
board to the motherboard connector, as well.
---------- Post updated at 12:15 PM ---------- Previous update was at 12:12 PM ----------
Otherwise I'd suggest you do a full backup with verification.
If the problem persists, then you can just continue to use it, knowing that it may fail at any moment,
but that you won't lose anything you can't easily reconstruct.
One thing about hard drives I can guarantee you: eventually all of them fail.
---------- Post updated at 12:19 PM ---------- Previous update was at 12:15 PM ----------
If you have a distro which can use SMART, and your disc is SMART capable, you can ask it.
Code:
smartctl -i /dev/hda
will tell you whether you have a SMART capable disc, and whether it be enabled. If your disc
is SMART capable, but it is not enabled, then enable it.
HI
We have some Red Hat Linux Sevres which is having TCP connection timeout, not SSH connection, as an example oracle connection connected from TOD.
SSH i managed to add keepalive and it's working fine (1 Reply)
hi all,
i had the below script
filename = /osa/data1/output.txt
printf '%27s%53s\n' ' CURRENT DATE' 26-08-2014 >> $filename
iam getting the ambigiuos redirect error in the 2nd line of the code...please guide me
regards,
vasa saikumar (3 Replies)
Hi Guys,
I just got this error:-
Your "cron" job on server2
/usr/5bin/ssh sysmgr@server1 /usr/local/bin/sudo /opt/local/pdm/bin/mount_pdmprod
produced the following output:
** /dev/rdsk/c1t5006016C446023DEd0s2
** /dev/rdsk/c1t5006016C446023DEd1s2
** /dev/rdsk/c1t5006016C446023DEd2s2... (2 Replies)
Hi All !
I am just trying to print bash variable in awk statement as string
here is my script
n=1
for file in `ls *.tk |sort -t"-" -k2n,2`; do
ak=`(awk 'FNR=='$n'{print $0}' res.dat)`
awk '{print "'$ak'",$0}' OFS="\t" $file
n=$((n+1))
unset ak
doneI am getting following error
awk:... (7 Replies)
i am facing an issue that the server give a connection timeout after 60 sec for any request more than that number . i tried to increase the TCP INTERVAL TIMEOUT from the default 60000 ms to more higher number.
the server seems to work fine and didn't give me the massage of the timeout but the... (0 Replies)
Here is an awk statement i am using to sum a series of numbers..
awk -F"," '{ for (i=1; i<=NF ; ++i) sum += $i;} # if (i > max) max=i }
END { s=""; for (i=1; i<=max; ++i) { printf "%s%s", s, sum; s=","; } printf "\n" }' filename.csv
It works fine for the summing part. But since my series... (19 Replies)
hi
i have created socket program with proper IP address and port no
client side port no 1085 and 1086
gateway side port no 1086 and 1085
and port no 1087 and 1088
receiver side port no 1088 and 1087
well it works fine on client and gateway side not on receiver and gateway side... (2 Replies)
Hi one of our Linux machine from our Data Farm have constantly hang and instable. I found out from the console the below error. Does anyone encounter this problem or see this error before with a glimpse on what it could be.. ?
---------------------------------------------------------------
... (1 Reply)
I'm getting a error on a old SPARC Station 5 system. The HDD I am using in internal 18GB. Everything use to work, and well wont now.
The error I am getting is in bootup. The error is 'Timeout waiting for ARP?RARP packet error'.
Anyone got any idea how I can fix this? I'm not sure... (4 Replies)
