10 More Discussions You Might Find Interesting
1. Solaris
Hello,
I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build.
The first part is what confuses me -the cabling.
I am coming from a Windows machine (w/appropriate... (5 Replies)
Discussion started by: joboy
5 Replies
2. Programming
Hi
I try to communicate with a GSM modem, from C, for sending SMS.
I use standart AT-commands.
Working well with terminal.
There is no problem writing ti the port.
But when I try to read I only get a echo, I write "ATI" and get "ATI" back, I should get somthing like "SIEMENS 35... (4 Replies)
Discussion started by: dmiller
4 Replies
3. Solaris
Hi Everyone,
In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies
4. UNIX for Dummies Questions & Answers
A neighbour's Ubuntu 10.04 machine has five serial ports, one on the motherboard and four on a PCI card. However, only four cards are showing:
# dmesg | grep tty
console enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
... (2 Replies)
Discussion started by: dotancohen
2 Replies
5. Solaris
What is the serial port on the T5140 used for. (4 Replies)
Discussion started by: pgsanders
4 Replies
6. AIX
Hi,
How can i configure my modem in AIX thru serial port (sa0-->tty0)
I have two port serial card configured as sa0
I created tty1 which port is tty0 and which port is tty1 how can i know?? (1 Reply)
Discussion started by: pchangba
1 Replies
7. Programming
I am developing an application in c with Linux OS, where a radio modem working at baud rate 9600 will be attached to PC on serial port. More than four such units will be communicating at one time, so there may be jamming or data corruption. Each module will be transmitting Data packets less than... (2 Replies)
Discussion started by: raj8109
2 Replies
8. UNIX for Advanced & Expert Users
I am using system running on red hat linux 4.
I had connected health measuring machine to the serial port and configured it
stty -F /dev/ttyS0 9600 -parenb cs8 -cstopb
this machine requires a command to be passed to it for giving output. I am unable to pass command hexa format(0x68) to the... (4 Replies)
Discussion started by: netsavant
4 Replies
9. Solaris
Hi,
I'm using Solaris workstation with 5.4 OS.
I was wondering if there's a way that I could
log the data incoming and outgoing on a certain
serial port.
Thanks in Advance! (1 Reply)
Discussion started by: uryuu
1 Replies
10. Programming
I'm writing a journal_write() function and I want it to:
- be a possible drop in replacement for write()
- write entries to the journal ;-) Could be a regular file (journal.txt), a serial printer or a // printer.
- handle printer status if needed.
fstat() tells weather or not we're dealing with... (2 Replies)
Discussion started by: starless
2 Replies
dc(4) Kernel Interfaces Manual dc(4)
Name
dc - serial line/mouse/keyboard
Syntax
device dc0 at ibus? vector dcintr
Description
The serial line controller provides four ports, with modem control on two of the ports. The DECstation 3100 and DECstation 2100 only pro-
vide partial modem control. The DECstation 5000 provides full modem control. The ports are used as follows:
Port Usage
0 Graphics device keyboard at 4800 BPS
1 Mouse or tablet at 4800 BPS
2 Communications port 1 (w/modem control)/local terminal
3 Communications port 2 (w/modem control)/local terminal
Each communication port from the serial line controller behaves as described in and can be set to run at any of 16 speeds. For the encod-
ing, see
When a graphics device is not being used as the system console, communications port 2 becomes the system console. In this configuration,
the port can only be used at 9600 BPS and no modem control is supported.
The serial line driver operates in interrupt-per-character mode (all pending characters are flushed from the silo on each interrupt).
Restrictions
Speed must be set to 9600 BPS on the console port and 4800 BPS on ports used by graphics devices. The serial line driver enforces this
restriction; that is, changing speeds with the command may not always work on these ports.
Files
console terminal
local terminal
local terminal
See Also
console(4), devio(4), tty(4), ttys(5), MAKEDEV(8)
RISC dc(4)