10 More Discussions You Might Find Interesting
1. Solaris
Hello,
I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build.
The first part is what confuses me -the cabling.
I am coming from a Windows machine (w/appropriate... (5 Replies)
Discussion started by: joboy
5 Replies
2. Programming
Hi
I try to communicate with a GSM modem, from C, for sending SMS.
I use standart AT-commands.
Working well with terminal.
There is no problem writing ti the port.
But when I try to read I only get a echo, I write "ATI" and get "ATI" back, I should get somthing like "SIEMENS 35... (4 Replies)
Discussion started by: dmiller
4 Replies
3. Solaris
Hi Everyone,
In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies
4. UNIX for Dummies Questions & Answers
A neighbour's Ubuntu 10.04 machine has five serial ports, one on the motherboard and four on a PCI card. However, only four cards are showing:
# dmesg | grep tty
console enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
... (2 Replies)
Discussion started by: dotancohen
2 Replies
5. Solaris
What is the serial port on the T5140 used for. (4 Replies)
Discussion started by: pgsanders
4 Replies
6. AIX
Hi,
How can i configure my modem in AIX thru serial port (sa0-->tty0)
I have two port serial card configured as sa0
I created tty1 which port is tty0 and which port is tty1 how can i know?? (1 Reply)
Discussion started by: pchangba
1 Replies
7. Programming
I am developing an application in c with Linux OS, where a radio modem working at baud rate 9600 will be attached to PC on serial port. More than four such units will be communicating at one time, so there may be jamming or data corruption. Each module will be transmitting Data packets less than... (2 Replies)
Discussion started by: raj8109
2 Replies
8. UNIX for Advanced & Expert Users
I am using system running on red hat linux 4.
I had connected health measuring machine to the serial port and configured it
stty -F /dev/ttyS0 9600 -parenb cs8 -cstopb
this machine requires a command to be passed to it for giving output. I am unable to pass command hexa format(0x68) to the... (4 Replies)
Discussion started by: netsavant
4 Replies
9. Solaris
Hi,
I'm using Solaris workstation with 5.4 OS.
I was wondering if there's a way that I could
log the data incoming and outgoing on a certain
serial port.
Thanks in Advance! (1 Reply)
Discussion started by: uryuu
1 Replies
10. Programming
I'm writing a journal_write() function and I want it to:
- be a possible drop in replacement for write()
- write entries to the journal ;-) Could be a regular file (journal.txt), a serial printer or a // printer.
- handle printer status if needed.
fstat() tells weather or not we're dealing with... (2 Replies)
Discussion started by: starless
2 Replies
UHSOCTL(1) BSD General Commands Manual UHSOCTL(1)
NAME
uhsoctl -- connection utility for Option based devices
SYNOPSIS
uhsoctl [-a apn] [-c cid] [-p pin] [-u username] [-k password] [-r path] [-f path] [-b | -n] interface
uhsoctl -d interface
uhsoctl -h
DESCRIPTION
uhsoctl is a small connection utility for Option N.V. devices that are based on Options packet interface and uses proprietary AT_* calls to
establish connections. The utility (tries to) configure both default route and name servers (/etc/resolv.conf).
By default uhsoctl detaches from the terminal upon on a successful connection, a few command-line options exists that allows this behavior to
be changed.
uhsoctl attempts to find a usable controlling serial port based on the provided network interface. If this fails you might specify a serial
port manually.
OPTIONS
-a apn
Specify APN to connect to.
-c cid
Specify CID (Context ID) to use, by default CID 1 is used. If an APN has been configured once, it's enough to specify the CID used for
further accesses.
-p pin
Specify SIM PIN.
-u username
Specify username.
-k password
Specify username.
-r path
Path to resolv.conf, default /etc/resolv.conf. Use /dev/null to disable updating of name servers.
-f path
Explicitly set the serial port to use as controlling terminal. Might be needed if the automatic detection fails.
-b Fork into background directly, before a connection has been established.
-n Never fork into background, run entirely in foreground.
EXAMPLES
Connect to ``apn.example.com'' on interface ``uhso0'' and use PIN ``1234'' to enable the SIM card.
uhsoctl -a apn.example.com -p 1234 uhso0
Disconnect from a previously established connection.
uhsoctl -d uhso0
SEE ALSO
uhso(4)
BSD
Aug 12, 2009 BSD