10 More Discussions You Might Find Interesting
1. Solaris
Hello,
I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build.
The first part is what confuses me -the cabling.
I am coming from a Windows machine (w/appropriate... (5 Replies)
Discussion started by: joboy
5 Replies
2. Programming
Hi
I try to communicate with a GSM modem, from C, for sending SMS.
I use standart AT-commands.
Working well with terminal.
There is no problem writing ti the port.
But when I try to read I only get a echo, I write "ATI" and get "ATI" back, I should get somthing like "SIEMENS 35... (4 Replies)
Discussion started by: dmiller
4 Replies
3. Solaris
Hi Everyone,
In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies
4. UNIX for Dummies Questions & Answers
A neighbour's Ubuntu 10.04 machine has five serial ports, one on the motherboard and four on a PCI card. However, only four cards are showing:
# dmesg | grep tty
console enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
... (2 Replies)
Discussion started by: dotancohen
2 Replies
5. Solaris
What is the serial port on the T5140 used for. (4 Replies)
Discussion started by: pgsanders
4 Replies
6. AIX
Hi,
How can i configure my modem in AIX thru serial port (sa0-->tty0)
I have two port serial card configured as sa0
I created tty1 which port is tty0 and which port is tty1 how can i know?? (1 Reply)
Discussion started by: pchangba
1 Replies
7. Programming
I am developing an application in c with Linux OS, where a radio modem working at baud rate 9600 will be attached to PC on serial port. More than four such units will be communicating at one time, so there may be jamming or data corruption. Each module will be transmitting Data packets less than... (2 Replies)
Discussion started by: raj8109
2 Replies
8. UNIX for Advanced & Expert Users
I am using system running on red hat linux 4.
I had connected health measuring machine to the serial port and configured it
stty -F /dev/ttyS0 9600 -parenb cs8 -cstopb
this machine requires a command to be passed to it for giving output. I am unable to pass command hexa format(0x68) to the... (4 Replies)
Discussion started by: netsavant
4 Replies
9. Solaris
Hi,
I'm using Solaris workstation with 5.4 OS.
I was wondering if there's a way that I could
log the data incoming and outgoing on a certain
serial port.
Thanks in Advance! (1 Reply)
Discussion started by: uryuu
1 Replies
10. Programming
I'm writing a journal_write() function and I want it to:
- be a possible drop in replacement for write()
- write entries to the journal ;-) Could be a regular file (journal.txt), a serial printer or a // printer.
- handle printer status if needed.
fstat() tells weather or not we're dealing with... (2 Replies)
Discussion started by: starless
2 Replies
PCWEASEL(4) BSD Kernel Interfaces Manual PCWEASEL(4)
NAME
pcweasel -- Support for the PC-Weasel serial console board
SYNOPSIS
pseudo-device pcweasel
weasel* at pci? dev ? function ?
Note that the appropriate display device must also be enabled. See pcdisplay(4) for more information.
DESCRIPTION
The PC-Weasel is a serial console board for use primarily on Intel-based PC-class systems. It addresses a problem that nearly everyone who
has deployed a PC-class server has experienced: the total lack of remote management capability on PC-class hardware.
In addition to serial console support, the PC-Weasel provides the ability to remotely reset the system (by means of a hardware reset signal),
and provides a watchdog timer function.
The PC-Weasel works by emulating the original IBM Monochrome Display Adapter (MDA). Writes to the display's character cells are translated
into ANSI terminal sequences which are then sent out the PC-Weasel's serial port. Incoming characters are translated into PC keyboard scan
codes and then fed (by means of a cable) into the system's keyboard controller. The system believes it is using a display console. This is
particularly important in the event that one needs access to BIOS configuration menus.
The PC-Weasel also includes a ST16550 serial port, which may be configured as any one of the system's serial ports. Typical usage is to con-
figure the port as com0 at ISA I/O address 0x3f8. When the PC-Weasel detects activity on the ST16550, the serial port is automatically con-
nected to the ST16550 so that the serial port may be used as normal. When the PC-Weasel detects activity on the internal UART used for MDA
emulation, the serial port is automatically reconnected to the emulation UART. This allows the boot program and kernel to be configured to
use the serial port directly (which is more efficient than using the MDA emulation mode), yet allows the MDA emulation to be reestablished as
soon as the kernel loses control of the system.
The pcweasel driver provides support for the additional features present on the PC-Weasel. At the moment, this includes support for the
watchdog timer function. Use of the pcweasel driver is not required in order for the system to function with a PC-Weasel installed so long
as only the MDA emulation and ST16550 serial port functionality is required.
SEE ALSO
pcdisplay(4), wdogctl(8)
HISTORY
The pcweasel driver first appeared in NetBSD 1.5.1.
AUTHORS
The PC-Weasel was invented by Herb Peyerl and Jonathan Levine at Canada Connect Corporation. It is now produced by Middle Digital, Inc.,
http://www.realweasel.com/
The pcweasel driver was written by Jason R. Thorpe <thorpej@zembu.com>, and contributed by Zembu Labs, Inc. Herb Peyerl of Middle Digital,
Inc. provided several firmware updates during the development of the driver.
BSD
November 23, 2007 BSD