Issue with a ethernet card

10 More Discussions You Might Find Interesting

1. Solaris

Problem with my Ethernet Card

Hi Gurus of Solaris. I have a problem yesterday when I was installing solaris in a x86 equipement I attached some log that I capture when I try to resolve the problem Any guru that can help please. Any command or procedure that I can run, please advice me Regards Andres

2. Solaris

Gigaswift ethernet card on reboot

I do have a server (SUNV240) with Solaris 9, it has a PCI gigaswift ethernet card for fiber with SC connector, everytime I reboot the server the card won't link up unless I unplug it and plug it back again, for remote operations this is a hassle since sometimes reboots are needed and this card...

3. Linux

Offload parameters for Ethernet Card

Hi, Actually i want to see Offload parameter for my Eth card. Then after i try using this command Anybody can explain ? Is there any problem with my eth card ?

4. AIX

Utilization of Ethernet Card

Hi, is it possible to find out network utilization of etherenet card in %? Regards, Manoj

5. Solaris

Ethernet card drivers issue...

I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do? Thanks in advance

6. UNIX for Dummies Questions & Answers

how can i see ethernet card speed in solars

hai this is nagesh when i was doing practical , i find some dought. iam using solaris 9. how can i see the ethernet card speed , wheather it is halfduplex or full duplex.any body please help me

7. IP Networking

ethernet card

What command do I use to show mw the ethernet card, I have tried ipconfig -a

8. UNIX for Dummies Questions & Answers

Ethernet card problem...

I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the...

9. IP Networking

RedHat and Ethernet card no like each other

I have searched this forum for solution and have drawn a blank... so I come to you for help :) I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the...

10. Filesystems, Disks and Memory

ethernet card for Solaris

Hi, How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this?

LEARN ABOUT REDHAT

axnet_cs

AXNET_CS(4)						     Kernel Interfaces Manual						       AXNET_CS(4)

NAME

       axnet_cs - Asix AX88190 chipset PCMCIA Ethernet Driver

SYNOPSIS

       insmod axnet_cs.o [pc_debug=n] [irq_list=i,j,...]

DESCRIPTION

       Axnet_cs  is  a driver for PCMCIA ethernet cards based on the Asix AX88190 chipset.  These cards are mostly NE2000 compatible but have sev-
       eral bugs that are sufficiently tricky to work around that a separate driver was deemed necessary.  When this driver is bound to a card, it
       allocates  the  next  available	ethernet  device (eth0..eth#).	This device name will be reported in the kernel log file, and passed on to
       cardmgr(8).

PARAMETERS

       pc_debug=n
	      Selects the PCMCIA debugging level.  This parameter is only available if the module is compiled with debugging enabled.  A  non-zero
	      value enables debugging.

       irq_list=i,j,...
	      Specifies the set of interrupts that may be allocated by this driver.

DIAGNOSTICS

       axnet_cs: this is not an AX88190 card!
	      Indicates that this card is probably a normal NE2000 compatible card, which requires the pcnet_cs driver.

       eth#: interrupt(s) dropped!
	      Indicates that the driver did not receive an interrupt notification for some reason.  The driver will poll the card (with a signifi-
	      cant performance penalty) if the problem persists.  The most likely cause is an interrupt conflict and/or host bridge  configuration
	      problem.

AUTHOR

       David Hinds - dahinds@users.sourceforge.net

SEE ALSO

       cardmgr(8), pcmcia(5).

pcmcia-cs							2001/08/17 12:51:58						       AXNET_CS(4)

SCO