Issue with a ethernet card

10 More Discussions You Might Find Interesting

1. Solaris

Problem with my Ethernet Card

Hi Gurus of Solaris. I have a problem yesterday when I was installing solaris in a x86 equipement I attached some log that I capture when I try to resolve the problem Any guru that can help please. Any command or procedure that I can run, please advice me Regards Andres

2. Solaris

Gigaswift ethernet card on reboot

I do have a server (SUNV240) with Solaris 9, it has a PCI gigaswift ethernet card for fiber with SC connector, everytime I reboot the server the card won't link up unless I unplug it and plug it back again, for remote operations this is a hassle since sometimes reboots are needed and this card...

3. Linux

Offload parameters for Ethernet Card

Hi, Actually i want to see Offload parameter for my Eth card. Then after i try using this command Anybody can explain ? Is there any problem with my eth card ?

4. AIX

Utilization of Ethernet Card

Hi, is it possible to find out network utilization of etherenet card in %? Regards, Manoj

5. Solaris

Ethernet card drivers issue...

I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do? Thanks in advance

6. UNIX for Dummies Questions & Answers

how can i see ethernet card speed in solars

hai this is nagesh when i was doing practical , i find some dought. iam using solaris 9. how can i see the ethernet card speed , wheather it is halfduplex or full duplex.any body please help me

7. IP Networking

ethernet card

What command do I use to show mw the ethernet card, I have tried ipconfig -a

8. UNIX for Dummies Questions & Answers

Ethernet card problem...

I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the...

9. IP Networking

RedHat and Ethernet card no like each other

I have searched this forum for solution and have drawn a blank... so I come to you for help :) I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the...

10. Filesystems, Disks and Memory

ethernet card for Solaris

Hi, How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this?

LEARN ABOUT FREEBSD

mfi

MFI(4)							   BSD Kernel Interfaces Manual 						    MFI(4)

NAME

     mfi -- LSI MegaRAID SAS driver

SYNOPSIS

     To compile this driver into the kernel, place the following lines in your kernel configuration file:

	   device pci
	   device mfi

     Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):

	   mfi_load="YES"

DESCRIPTION

     This driver is for LSI's next generation PCI Express SAS RAID controllers.  Access to RAID arrays (logical disks) from this driver is pro-
     vided via /dev/mfid? device nodes.  A simple management interface is also provided on a per-controller basis via the /dev/mfi? device node.

     The mfi name is derived from the phrase "MegaRAID Firmware Interface", which is substantially different than the old "MegaRAID" interface and
     thus requires a new driver.  Older SCSI and SATA MegaRAID cards are supported by amr(4) and will not work with this driver.

     Two sysctls are provided to tune the mfi driver's behavior when a request is made to remove a mounted volume.  By default the driver will
     disallow any requests to remove a mounted volume.	If the sysctl dev.mfi.%d.delete_busy_volumes is set to 1, then the driver will allow
     mounted volumes to be removed.

     A tunable is provided to adjust the mfi driver's behaviour when attaching to a card.  By default the driver will attach to all known cards
     with high probe priority.	If the tunable hw.mfi.mrsas_enable is set to 1, then the driver will reduce its probe priority to allow mrsas to
     attach to the card instead of mfi.

HARDWARE

     The mfi driver supports the following hardware:

     o	 LSI MegaRAID SAS 1078
     o	 LSI MegaRAID SAS 8408E
     o	 LSI MegaRAID SAS 8480E
     o	 LSI MegaRAID SAS 9240
     o	 LSI MegaRAID SAS 9260
     o	 Dell PERC5
     o	 Dell PERC6
     o	 IBM ServeRAID M1015 SAS/SATA
     o	 IBM ServeRAID M1115 SAS/SATA
     o	 IBM ServeRAID M5015 SAS/SATA
     o	 IBM ServeRAID M5110 SAS/SATA
     o	 IBM ServeRAID-MR10i
     o	 Intel RAID Controller SRCSAS18E
     o	 Intel RAID Controller SROMBSAS18E

FILES

     /dev/mfid?  array/logical disk interface
     /dev/mfi?	 management interface

DIAGNOSTICS

     mfid%d: Unable to delete busy device  An attempt was made to remove a mounted volume.

SEE ALSO

     amr(4), pci(4), mfiutil(8)

HISTORY

     The mfi driver first appeared in FreeBSD 6.1.

AUTHORS

     The mfi driver and this manual page were written by Scott Long <scottl@FreeBSD.org>.

BUGS

     The driver does not support big-endian architectures at this time.

BSD
								   July 15, 2013							       BSD

SCO