10 More Discussions You Might Find Interesting
1. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
2. Solaris
I do have a server (SUNV240) with Solaris 9, it has a PCI gigaswift ethernet card for fiber with SC connector, everytime I reboot the server the card won't link up unless I unplug it and plug it back again, for remote operations this is a hassle since sometimes reboots are needed and this card... (3 Replies)
Discussion started by: xe2bss
3 Replies
3. Linux
Hi,
Actually i want to see Offload parameter for my Eth card.
Then after i try using this command
Anybody can explain ?
Is there any problem with my eth card ? (1 Reply)
Discussion started by: justbow
1 Replies
4. AIX
Hi,
is it possible to find out network utilization of etherenet card in %?
Regards,
Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies
5. Solaris
I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do?
Thanks in advance (2 Replies)
Discussion started by: younus_syed
2 Replies
6. UNIX for Dummies Questions & Answers
hai this is nagesh
when i was doing practical , i find some dought.
iam using solaris 9. how can i see the ethernet card speed , wheather it is halfduplex or full duplex.any body please help me (4 Replies)
Discussion started by: nag.mi2000
4 Replies
7. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
8. UNIX for Dummies Questions & Answers
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies
9. IP Networking
I have searched this forum for solution and have drawn a blank... so I come to you for help :)
I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies
10. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
CARDMGR(8) System Manager's Manual CARDMGR(8)
NAME
cardmgr - PCMCIA device manager
SYNOPSIS
cardmgr [-V] [-q] [-d] [-o] [-f] [-v] [-c configpath] [-m modpath] [-p pidfile] [-s stabfile]
DESCRIPTION
Cardmgr monitors PCMCIA sockets for card insertion and removal events. When a card is inserted, cardmgr looks up the card in a database of
known cards. If the card can be identified, appropriate device drivers will be loaded and bound to the card. When a card is ejected, that
card's drivers will be shut down and unloaded if possible. Based on the contents of the PCMCIA card configuration database, cardmgr may
also execute arbitrary commands when appropriate cards are either inserted or removed.
All insertion and removal events, device driver loads and unloads, and startup and shutdown commands are reported in the system log file.
Warnings and errors will also be logged. Current card and device information for each socket is recorded in /var/lib/pcmcia/stab.
Normally, when a card is identified, cardmgr will send a beep to the console. A beep is also generated when a card is successfully config-
ured. A beep of lower pitch is generated if either of these steps fails. Ejecting a card produces a single beep.
When cardmgr receives a SIGHUP signal, it will reload its configuration file. When cardmgr receives a SIGTERM signal, it will shut down
all sockets that are not busy and then exit, but drivers for busy sockets will stay loaded.
If the PCMCIA_OPTS environment variable is set, its contents will be parsed after the main card configuration file is read.
At startup, cardmgr requires that /tmp reside on a filesystem that permits special device files (i.e., a real linux filesystem, that is not
mounted "nodev").
OPTIONS
-V Show version information and exit.
-q Quiet mode: don't beep when cards are inserted.
-v Verbose mode: generates more informational messages during normal operation. Configuration scripts are executed with VERBOSE=y.
-d Follow module dependencies when loading driver modules, by defaulting to use modprobe instead of insmod. Normally, cardmgr will try
using modprobe only after an unsuccessful attempt with insmod.
-f Foreground: do not fork and run as a daemon until after configuring any cards that are already present.
-o One pass: configure cards that are present, then exit. This flag also forces cardmgr to run in the foreground.
-c configpath
Look for the card configuration database and card configuration scripts in the specified directory, instead of /etc/pcmcia.
-m modpath
Look for loadable kernel modules in the specified directory, instead of /lib/modules/`uname -r`.
-p pidfile
Write the PID of the cardmgr process to the specified file, instead of /var/run/cardmgr.pid.
-s stabfile
Write current socket information to the specified file, instead of /var/lib/pcmcia/stab.
FILES
/etc/pcmcia/config Card configuration database
/etc/pcmcia/config.opts Local resource settings for PCMCIA devices
/var/run/cardmgr.pid PID of active cardmgr process
/var/lib/pcmcia/stab Current card and device information for each socket.
AUTHOR
David Hinds - dahinds@users.sourceforge.net
SEE ALSO
pcmcia(5), stab(5), cardctl(8), cardinfo(1).
pcmcia-cs 2001/07/19 23:41:34 CARDMGR(8)