Issue with a ethernet card

10 More Discussions You Might Find Interesting

1. Solaris

Problem with my Ethernet Card

Hi Gurus of Solaris. I have a problem yesterday when I was installing solaris in a x86 equipement I attached some log that I capture when I try to resolve the problem Any guru that can help please. Any command or procedure that I can run, please advice me Regards Andres

2. Solaris

Gigaswift ethernet card on reboot

I do have a server (SUNV240) with Solaris 9, it has a PCI gigaswift ethernet card for fiber with SC connector, everytime I reboot the server the card won't link up unless I unplug it and plug it back again, for remote operations this is a hassle since sometimes reboots are needed and this card...

3. Linux

Offload parameters for Ethernet Card

Hi, Actually i want to see Offload parameter for my Eth card. Then after i try using this command Anybody can explain ? Is there any problem with my eth card ?

4. AIX

Utilization of Ethernet Card

Hi, is it possible to find out network utilization of etherenet card in %? Regards, Manoj

5. Solaris

Ethernet card drivers issue...

I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do? Thanks in advance

6. UNIX for Dummies Questions & Answers

how can i see ethernet card speed in solars

hai this is nagesh when i was doing practical , i find some dought. iam using solaris 9. how can i see the ethernet card speed , wheather it is halfduplex or full duplex.any body please help me

7. IP Networking

ethernet card

What command do I use to show mw the ethernet card, I have tried ipconfig -a

8. UNIX for Dummies Questions & Answers

Ethernet card problem...

I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the...

9. IP Networking

RedHat and Ethernet card no like each other

I have searched this forum for solution and have drawn a blank... so I come to you for help :) I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the...

10. Filesystems, Disks and Memory

ethernet card for Solaris

Hi, How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this?

LEARN ABOUT REDHAT

memory_cb

MEMORY_CS(4)						     Kernel Interfaces Manual						      MEMORY_CS(4)

NAME

       memory_cb - CardBus memory driver

SYNOPSIS

       insmod memory_cb.o [pc_debug=n]

DESCRIPTION

       Memory_cb gives direct memory access to the address spaces of CardBus cards.  It provides character-mode devices for accessing a card's PCI
       configuration space, up to six mapped memory or IO regions, and its expansion ROM space.  When loaded, memory_cb will allocate a free major
       device number.  For each card, it will report which address spaces are available, and their sizes.  Minor numbers have the form 'dddddsss',
       where 'ddddd' is the instance number and 'sss' is the memory space for that instance.  When memory_cb is bound to a card,  it  will  report
       its major and minor device numbers to cardmgr(8).

       The default memory card initialization script creates device special files for all eight card address spaces, though for a particular card,
       some of these may be unavailable.  These devices have the following names:

       /dev/cbmem#s0
	      The card's PCI configuration space.

       /dev/cbmem#s[1-6]
	      The IO or memory spaces mapped by the card's six Base Address Registers.

       /dev/cbmem#s7
	      The card's expansion ROM space.

       The character special devices can be used to read and write arbitrary numbers of bytes to arbitrary locations.  The memory_cb driver can be
       bound to any card regardless of function.

PARAMETERS

       pc_debug=n
	      Selects  the PCMCIA debugging level.  This parameter is only available if the module is compiled with debugging enabled.	A non-zero
	      value enables debugging.

AUTHOR

       David Hinds - dahinds@users.sourceforge.net

SEE ALSO

       cardmgr(8), pcmcia(5), memory_cs(4).

pcmcia-cs							2000/06/12 21:24:48						      MEMORY_CS(4)

SCO