Configuring Broadcom BCM5721 NetXtreme Gigabit Ethernet

10 More Discussions You Might Find Interesting

1. Solaris

Broadcom driver for Solaris

I'm having the hardest time finding the Broadcom drivers for Solaris. I need an odd ball, 32-bit for Solaris 10. Anyone know where I can find one?

2. Hardware

Need Sun 10-Gigabit Ethernet Adapter CD or ixge driver

Hi, Does anybody have a "Sun 10-Gigabit Ethernet Adapter installation CD" or driver ixge for Sun 10-Gigabit Ethernet PCI-X adapter? I need it but can't find it anywhere. So if you know where I can download it or purchase it, please let me know. (Already tried Oracle's website, don't have it) ...

3. AIX

vio server ethernet to vio client ethernet(concepts confusing)

Hi In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID. Similarly how does the vio client partition gets the virtual ethernet scsi client adapter...

4. Solaris

SUN GIGABIT ETHERNET CARD

Hi, we have SUN Gigabit ethernet cards at the server, both have 2 lines connected but hiw can I found out which cable is on which port before I configure it: the cards has 4 ports , from right to left the cables are connected at the first right then 2 empty then the last at the left side. ...

5. BSD

Broadcom 4312 in BSD

Is there a way to configure Broadocom wifi 4312 in a bsd system, FreeBSD or OpenBSD. I will appreciate any kind of help. Thanks in advance

6. IP Networking

Gigabit Link throughput

As a rule of thumb in doing calculations, what figure would you use in Mbytes/sec? I know the answer varies grealty on the topolgy of the network but I wonde what newteok engineers use a rough rule of thumb? Many thanks.

7. Solaris

Solaris 10 and Broadcom drivers

Hi to all, I've installed Solaris 10 on my workstation but I've some networks problems.My NIC,a Broadcom integrated chipset don't work with solaris.Whit the prtconf command I'm unable to identify the correct chipset's model.And I'm searching hovewer for some drivers but I'm fear that Broadcom...

8. Solaris

Configuring TP Ethernet SS5 Solaris 8

Hey. how do i configure the Lance Ethernet in my SS5 i must use DHCP to get Internet access. i have tried sys-unconfig and ifconfig le0 plumb and dhcp. but no cigar. how do i configure ? i have had some problems with the /etc/hosts dir. it says it dosent exist and when i try to create it it says...

9. Solaris

Configuring TP Ethernet in SPARCstation 5 Solaris 8

Hey. i have been trying to configure the on board Ethernet in My Sparcstation 5, i have spent a lot of time on the ifconfig man pages. but it could really be nice with some pro. help. i don't think the interface is running . i don't know what name the interface have, le0 eth0 et0, it just says no...

10. AIX

Network performance problem between AIX and SUN ethernet gigabit

I am posting this as an FYI. I burned a lot of time on digging for this solution. The problem was performance between newer AIX p series boxes and a sun 4500 with a fiber nic. I tried many misc. solutions but this turned out to fix the issue. My bandwidth benchmark went from around 20MB/sec to...

LEARN ABOUT CENTOS

iscsiuio

iscsiuio(8)						      System Manager's Manual						       iscsiuio(8)

NAME

       iscsiuio - iSCSI UserSpace I/O driver

SYNOPSIS

       iscsiuio [-d-f-v]

DESCRIPTION

       iscsiuio  is  the  UserSpace I/O driver for the Broadcom NetXtreme II BCM5706/5708/5709 series PCI/PCI-X Gigabit Ethernet Network Interface
       Card (NIC) and for the Broadcom NetXtreme II BCM57710/57711/57712/57800/57810/57840 series PCI-E  10  Gigabit  Ethernet	Network  Interface
       Card.  The driver has been tested on 2.6.28 kernels and above.

       Refer to the README.TXT from the driver package on how to compile and install the driver.

       Refer to various Linux documentations on how to configure network protocol and address.

DRIVER DEPENDENCIES

PARAMETERS

       There are very few parameters when running this application.

       -d<debuglevel>
	      This is to enable debug mode where debug messages will be sent to stdout The following debug modes are supported

	      DEBUG	    4 - Print all messages

	      INFO	    3 - Print messages needed to follow the uIP code (default)

	      WARN	    2 - Print warning messages

	      ERROR	    1 - Only print critical errors

       -f     This is to enable forground mode so that this application doesn't get sent into the background.

       -v     This is to print the version.

       -p<pidfile>
	      Use pidfile (default  /var/run/iscsiuio.pid )

       -h     Display this help and exit.

AUTHOR

       Benjamin Li - benli@broadcom.com

       Eddie Wai - eddie.wai@broadcom.com

Broadcom Corporation						    12/10/2013							       iscsiuio(8)

SCO