SCO unix server performance tuning

9 More Discussions You Might Find Interesting

1. AIX

UNIX/AIX Performance Tuning = some basics please

Hi all, From Googling, I found that the basics used for troubleshooting UNIX/AIX performance issues are commands like vmstat, iostat and sar. I believe these are generic commands regardless of what UNIX flavour is in used, only difference being is the format of the output. In a real case...

2. Shell Programming and Scripting

Single command for add 2 columns and remove 2 columns in unix/performance tuning

Hi all, I have created a script which adding two columns and removing two columns for all files. Filename: Cust_information_1200_201010.txt Source Data: "1","Cust information","123","106001","street","1-203 high street" "1","Cust information","124","105001","street","1-203 high street" ...

3. Shell Programming and Scripting

Performance Tuning

Hi All, In last one week, i have posted many questions in this portal. At last i am succeeded to make my 1st unix script. following are 2 points where my script is taking tooooo long. 1. Print the total number of records excluding header & footer. I have found that awk 'END{print NR -...

4. UNIX for Dummies Questions & Answers

Tuning Unix server memory - HPUX11i

Hello, I'm using a unix server (HP rp2450) which has : 2 Go RAM memory and 4 Go swap. Here is the result of vmstat -n command : $ vmstat -n VM memory page faults avm free re at pi po fr de sr in sy ...

5. Shell Programming and Scripting

Oracle-performance tuning

Sorry, This is out of scope of this group.But I require the clarification pretty urgently. My Oracle database is parallely enabled. Still,in a particular table queries do not work "parallely" always. How is this?

6. UNIX for Dummies Questions & Answers

Performance Tuning

Hi to all, I'm interested in finding an introduction about Performance Tuning under Unix (or Linux); can somebody please point me in the right direction? Best regards

7. Filesystems, Disks and Memory

EXT3 Performance tuning

Hi all, long time ago I posted something, but now, it is needed again :( Currently, I am handling with a big NFS Server for more than 200 clients, this sever has to work with 256 NFSDs. Because of this huge amount of NFSDs, there are thousands of small write accesses down to the disk and...

8. SCO

SCO UNIX performance

Hi there, Our server is SCO UNIX 3.12 (ten years old). Recently, the system is so slow even there were only a few users logging on the system. Please advise me, Thank you so much, Trinh

9. UNIX for Dummies Questions & Answers

Performance tuning.

can someone tell me a good site to go to in order to learn this. please do not recommen nay books because i dont have interest in that. if you know of any good sites with good straight forward explanation on how to split loads on machines that has excessive loading, please let me know Also,...

LEARN ABOUT SUSE

x11perfcomp

X11PERFCOMP(1)						      General Commands Manual						    X11PERFCOMP(1)

NAME

       x11perfcomp - X11 server performance comparison program

SYNTAX

       x11perfcomp [ -r | -ro ] [ -l label_file ] files

DESCRIPTION

       The  x11perfcomp program merges the output of several x11perf(1) runs into a nice tabular format.  It takes the results in each file, fills
       in any missing test results if necessary, and for each test shows the objects/second rate of each server.  If invoked with the  -r  or  -ro
       options, it shows the relative performance of each server to the first server.

       Normally,  x11perfcomp  uses  the first file specified to determine which specific tests it should report on.  Some (non-DEC :) servers may
       fail to perform all tests.  In this case, x11perfcomp automatically substitutes in a rate of 0.0  objects/second.   Since  the  first  file
       determines  which  tests  to  report  on, this file must contain a superset of the tests reported in the other files, else x11perfcomp will
       fail.

       You can provide an explicit list of tests to report on by using the -l switch to specify a file of labels.  You can create a label file	by
       using the -label option in x11perf.

OPTIONS

       x11perfcomp accepts the options listed below:

       -r	       Specifies that the output should also include relative server performance.

       -ro	       Specifies that the output should include only relative server performance.

       -l label_file   Specifies a label file to use.

X DEFAULTS

       There are no X defaults used by this program.

SEE ALSO

       X(7), x11perf(1)

AUTHORS

       Mark Moraes wrote the original scripts to compare servers.
       Joel McCormack just munged them together a bit.

X Version 11							   x11perf 1.5.1						    X11PERFCOMP(1)

SCO