10 More Discussions You Might Find Interesting
1. SCO
I am currently having a problem with my SCO OpenServer 5.0.5 / 3.2v5.0.5 system.
Running smoothly for the past 3 years, at random on March 16, 2010 the system crashes. I reboot it. Everything is normal again. 9 hours later it crashes again. This cycle has repeated itself ever since then. System... (2 Replies)
Discussion started by: jesmith
2 Replies
2. SCO
hello i have a problem with mouse in vmware with sco 5.0.6
in graphic mode X11 my mouse move to corner after a while
do you have any idea about this problem
vmware 6.5.2
vmware 7 (5 Replies)
Discussion started by: kaydream
5 Replies
3. UNIX for Dummies Questions & Answers
I rlogin from a sco box to a redhat box and run /bin/vi. Pgup, Pgdn, and arrow up/down keys don't work. I enter "export TERM=ansi80x25" and run vi again.Everything works just like I like it. Except the cursor turns into a blinking overscore. When I exit vi and close the connection to redhat,... (2 Replies)
Discussion started by: bussyw
2 Replies
4. SCO
Help Please ,
how to shutdown SCO v. 5.0.5 from client pc ( windows xp or 2000 ) ? i have full access from client and i need to shutdown SCO from windows (2 Replies)
Discussion started by: rabih_saleh
2 Replies
5. SCO
We are using GTAR for daily copies of our database using Travan cartridges (Tapestor drive)and are having intermittent problems. Some days it does not copy and we can't figure out why. Sometimes it seems to be hanging and a tape status command doesn't return anything. Other times it doesn't copy... (0 Replies)
Discussion started by: Yrr88
0 Replies
6. SCO
Hi everyone,
We r installing sco openserver 5.07 on dell poweredge 2800 but we are facing problem when installing SCSI-raid drivers. Dell provide Perc4 raid card and we dont found raid drivers for this specific raid card. So we r stuck up on primary stage and we also dont know the... (2 Replies)
Discussion started by: mineshkoli
2 Replies
7. SCO
Hi All,
I just tried to intall Unix ware SCO version 7 on my computer but when system first boots from the CD The terminal Emulator does not shows texts in correct form; it shows all the text in Obnoxious form which is unable to read. I have ATI Radeon 9000 Graphics card installed on my... (0 Replies)
Discussion started by: monster12
0 Replies
8. UNIX for Dummies Questions & Answers
I tryed to install SCO 5.0.6 OpenServer on P4 2.0 GHz 384 MB ram 40 GB HDD. It booted from the floppy disk, and when it comes to hd_config I got this error:
unexpected trap in kernel mode:
PANIC: K_trap - kernel mode trap 0x0000000E
** Safe to power off **
Please, what should I do? (1 Reply)
Discussion started by: Guest07
1 Replies
9. Filesystems, Disks and Memory
Hello all,
I'm trying to install SCO openserver 5 on a 2.5 Gig hard drive, and I tried fdisk and a low-level format of the drive. When I insert the boot diskette all seems fine, and it asks me to set the cd-rom and it sees it and reads from it. Well, I'm thinking all is well until right after I... (1 Reply)
Discussion started by: immulett
1 Replies
10. UNIX for Advanced & Expert Users
Hardware:
IBM 300PL
32MB RAM
60Gig HDD
During the phase in SCO installation where I get to partition my hard disk, SCO only seems to see 8Gig out of the 60 that I have.
Does anyone out there know of a utility or what I need to do to make the the whole 60Gig available.
Thanks (3 Replies)
Discussion started by: budrito
3 Replies
iscc(7) Miscellaneous Information Manual iscc(7)
NAME
iscc - serial communications interface
SYNOPSIS
controller iscc0 at isa0
DESCRIPTION
An onboard Zilog 8530 DUART provides AXPvme-based Single Board Computers with console (CON) and auxiliary (AUX) serial communications
ports. Both serial communications ports can operate at baud rates from B50 to B38400, excluding B134 (see tty(7)).
On AXPvme Single Board Computers configured with a graphics head as the system console, the CON serial communications port (/dev/tty01) is
available for use by application programs as an additional communications port.
In the absence of a graphics head, the CON serial communications port (/dev/console) becomes the system console. When used as the serial
system console, the CON serial communications port always operates at 9600 BPS, 8-bits, and no parity.
Regardless of system console, the AUX serial communications port (/dev/tty00) is always available for use by application programs.
RESTRICTIONS
Data communications equipment attached to the CON serial communications port must be set to 9600 BPS, 8-bits, no parity when configured as
the serial system console. The iscc terminal driver enforces this restriction.
No modem control is supported for either the CON or AUX serial communications ports.
FILES
console terminal local terminal local terminal
RELATED INFORMATION
console(7), devio(7), tty(7), MAKEDEV(8) delim off
iscc(7)