10 More Discussions You Might Find Interesting
1. UNIX for Beginners Questions & Answers
We have a legacy system that runs on SCO OpenServer 5.0.6, and I've rebuilt the server a couple of times so we can have access to old historical data. That system suddenly went offline for no known reason, and I know that the configuration has not been altered, there is nobody with access to the... (63 Replies)
Discussion started by: spock9458
63 Replies
2. SCO
hi
i have image SCo Unix 5.0.6 and I want transfer on my HP ML350 G5
after Transfer show this message :
boot not found
cannot open
stage 1 boot failure: error loading hd (40)/boot
this hp server used smart array E200i and P400 and sco not recognized HDD
tanks (7 Replies)
Discussion started by: moein.mojtaba
7 Replies
3. SCO
Our system is not booting up properly. It keeps going to this screen:
Enter Run Level (0-6, s or S):
I tried to hit all nos# 0-6 is just goes to hung state.
Tried s or S & it brings me to single user mode. I've checked the file systems & found out that all three had 98%. I tried to... (86 Replies)
Discussion started by: jedimaster
86 Replies
4. SCO
Hello those more knowledgeable than I:
I have been trying to get xp and SCO to coexist on the same system. I have tried several different ways to make both work, here's the list:
-install xp, image it, move the partition to the end of drive, verify it boots, image again,
-boot off of SCO... (6 Replies)
Discussion started by: stay0ut
6 Replies
5. UNIX for Dummies Questions & Answers
Just installing 5.0.5 on a DELL OPTIFLEX GX520. Using a 40GB IDE Drive.
Installation appeared to work but on rebooting it hangs at the "LOADING KERNEL hd(40)unix.bss
Any ideas please (1 Reply)
Discussion started by: farmacy
1 Replies
6. UNIX for Dummies Questions & Answers
I have been passed a SCO OS5 server that will not boot up, Im a UNIX starter to say the least, So I was wondering if Im dealing with something simple and I dont know it!
The server starts up to the Boot prompt and in either multiple or single mode it will stop during the boot process and wait. ... (0 Replies)
Discussion started by: cscmsupport
0 Replies
7. SCO
hi, i m a newbie and installed sco unix on my machine. Also i installed win-xp. i tried to modify the boot.ini file but it does not give me a choice in the begining.
please guide me on this. do we get a boot loader for unix like LILO or GRUB?
:confused: (3 Replies)
Discussion started by: 187final
3 Replies
8. UNIX for Advanced & Expert Users
Hi friends,
i am getting the following error while booting my system which has SCo UNIX .
=========================
H iinit
PANIC: srmountfun-Error 22
mounting of rootdev hd(1/42)
cannot dump 40863 pages to dempdev hd(1/41) : Space for only 0 pages.
Dump not completed.
safe to power off... (3 Replies)
Discussion started by: sveera
3 Replies
9. UNIX for Dummies Questions & Answers
hello guys.
I just installed SCO 5.0.6 OpenServer it went all the way to the end of the installation and the first boot try it gave me this message.
not a directory
boot not found
cannot open
stage 1 boot failure: error loading hd (40)/boot (2 Replies)
Discussion started by: josramon
2 Replies
10. UNIX for Dummies Questions & Answers
This last monday the inittab file became corrupted and the server refused to start... A set of boot / root disks made from another SCO server saved the day.. Anyway, I would like to make a set from the production server just so I have a set created from that machine. The command I would be using is... (1 Reply)
Discussion started by: LowOrderBit
1 Replies
BRANDELF(1) BSD General Commands Manual BRANDELF(1)
NAME
brandelf -- mark an ELF binary for a specific ABI
SYNOPSIS
brandelf [-lv] [-f ELF_ABI_number] [-t string] file ...
DESCRIPTION
The brandelf utility marks an ELF binary to be run under a certain ABI for FreeBSD.
The options are as follows:
-f ELF_ABI_number
Forces branding with the supplied ELF ABI number. Incompatible with the -t option. These values are assigned by SCO/USL.
-l Writes the list of all known ELF types to the standard error.
-v Turns on verbose output.
-t string
Brands the given ELF binaries to be of the string ABI type. Currently supported ABIs are ``FreeBSD'', ``Linux'', and ``SVR4''.
file If -t string is given it will brand file to be of type string, otherwise it will simply display the branding of file.
EXIT STATUS
Exit status is 0 on success, and 1 if the command fails if a file does not exist, is too short, fails to brand properly, or the brand
requested is not one of the known types and the -f option is not set.
EXAMPLES
The following is an example of a typical usage of the brandelf command:
brandelf file
brandelf -t Linux file
SEE ALSO
The Santa Cruz Operation, Inc., System V Application Binary Interface, http://www.sco.com/developer/devspecs/, April 29, 1998 (DRAFT).
HISTORY
The brandelf manual page first appeared in FreeBSD 2.2.
AUTHORS
This manual page was written by John-Mark Gurney <jmg@FreeBSD.org>.
BSD
March 25, 2014 BSD