10 More Discussions You Might Find Interesting
1. Linux
I know Xenix is a little outdated, and is dangerous to use on network.
But this is a virtual machine, and I like to play retrocomputing sometime.
The question is..why ftp over slip doesn't work?
I've set this Xenix vm on libvirt
<domain type='kvm' id='5'... (2 Replies)
Discussion started by: Linusolaradm1
2 Replies
2. UNIX for Dummies Questions & Answers
Hey all,
At my work we have an installation that runs on a Xenix System V coupled with a PLC.
Now I have to take a backup of the complete Hard Disk from the PC but have no idea how to manage this.
Could someone help me and tell me which steps I have to take.
Thanx. (8 Replies)
Discussion started by: sideshow bob
8 Replies
3. SCO
Hi I am looking for sco xenix ar command under sco unix. please help me ! (4 Replies)
Discussion started by: javad1_maroofi
4 Replies
4. SCO
Hi i have a problem after boot with N1 disk and putting N2 disk and pressing the enter in this message:Insert N2(filesystem) floppy and press after by this(pressing enter) the system is reboot!! why??? :confused:
my old pc is a Pentium II 333mhz 3gb hd 64mb ram
please help!! :( (3 Replies)
Discussion started by: panos_pit
3 Replies
5. SCO
Hello - I'm a newbie to these forums. Please excuse me if I am posting in the wrong area. My dilemma. The HD on our ancient Xenix system apparently is full. I receive the "no space on dev 1/40" prompt. This occurred after I attempted to purge some unwanted files. This system runs our small... (1 Reply)
Discussion started by: gmbrickley
1 Replies
6. UNIX for Advanced & Expert Users
I am taking an old xenix drive and installing it in a recent SCO Build Server. I have gone through the process of running mkdev hd twice since the drive is a SCSI then proceed to run mkdev fs and when I attempt to add one of the shown partitions I get the following:
fsck: cannot determine... (1 Reply)
Discussion started by: justenglabs
1 Replies
7. Linux
Is there anything I should know about kernel versions and how they are numbered?
I'm trying to compile ivtv drivers. When I run make, the first check is the kernel version. uname -r shows my kernel as 2.6.8-2-386, but I get the error:
ivtv-0.6.0 does NOT support kernels > 2.6.16!
Is this... (1 Reply)
Discussion started by: System Shock
1 Replies
8. SCO
Hey everyone! I'm trying to retrieve old files from my Xenix computers. So the option I've now come down to is to load up a second harddrive and do a doscp of my tar'd backup file. Now, How do I go about this? I am not a unix user myself so I'm not quite sure. I need help! I have a VERY short... (1 Reply)
Discussion started by: Slaughter
1 Replies
9. UNIX for Dummies Questions & Answers
Randomly receive the following message:
"Can not open line tty1a device busy error 16"
and
"/etc/getty/t60 tty1a"
What is causing this error message ? (1 Reply)
Discussion started by: jbartok
1 Replies
10. HP-UX
We just went from HP-UX 10.20 to 11.00.
All the bugs are out, except for a small detail...the old 9-track isn't working.
We receive large amounts of data on reel-to-reel so I kinda need it fixed. In the meantime, I'm trying to see if they can send me a DAT tape instead.
I'm pretty sure the drive... (8 Replies)
Discussion started by: ncmurf00
8 Replies
SYSCTL.CONF(5) BSD File Formats Manual SYSCTL.CONF(5)
NAME
sysctl.conf -- kernel state defaults
DESCRIPTION
The /etc/sysctl.conf file is read in when the system goes into multi-user mode to set default settings for the kernel. The /etc/sysctl.conf
is in the format of the sysctl(8) command, i.e.
sysctl_mib=value
Comments are denoted by a ``#'' at the beginning of a line. Comments can also exist at the end of a line, as seen in the EXAMPLES section,
below.
FILES
/etc/sysctl.conf Initial settings for sysctl(8).
EXAMPLES
To turn off logging of programs that exit due to fatal signals you may use a configuration like
# Configure logging.
kern.logsigexit=0 # Do not log fatal signal exits (e.g. sig 11)
SEE ALSO
rc.conf(5), rc(8), sysctl(8)
HISTORY
The sysctl.conf file appeared in FreeBSD 4.0.
BUGS
If loadable kernel modules are used to introduce additional kernel functionality and sysctls to manage that functionality, sysctl.conf may be
processed too early in the boot process to set those sysctls. For example, sysctls to manage the linux emulator cannot be set in sysctl.conf
if the linux emulator is loaded as a module rather than compiled into the kernel.
BSD
December 30, 1999 BSD