Problem with dinosaur's kernel - Xenix 386 2.3.4


 
Thread Tools Search this Thread
Operating Systems SCO Problem with dinosaur's kernel - Xenix 386 2.3.4
# 1  
Old 05-18-2005
Problem with dinosaur's kernel - Xenix 386 2.3.4

After booting from the N1 floppy I see:

kernel: WARNING: No floating point emulator found in /etc/emulator
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. Linux

A little difficult: investigate Xenix and slattach problem

I know Xenix is a little outdated, and is dangerous to use on network. But this is a virtual machine, and I like to play retrocomputing sometime. The question is..why ftp over slip doesn't work? I've set this Xenix vm on libvirt <domain type='kvm' id='5'... (2 Replies)
Discussion started by: Linusolaradm1
2 Replies

2. UNIX for Dummies Questions & Answers

Backup Hard Disk Xenix System V

Hey all, At my work we have an installation that runs on a Xenix System V coupled with a PLC. Now I have to take a backup of the complete Hard Disk from the PC but have no idea how to manage this. Could someone help me and tell me which steps I have to take. Thanx. (8 Replies)
Discussion started by: sideshow bob
8 Replies

3. SCO

SCO Xenix AR command ?

Hi I am looking for sco xenix ar command under sco unix. please help me ! (4 Replies)
Discussion started by: javad1_maroofi
4 Replies

4. SCO

Sco unix v/386 3.2 problem boot and install

Hi i have a problem after boot with N1 disk and putting N2 disk and pressing the enter in this message:Insert N2(filesystem) floppy and press after by this(pressing enter) the system is reboot!! why??? :confused: my old pc is a Pentium II 333mhz 3gb hd 64mb ram please help!! :( (3 Replies)
Discussion started by: panos_pit
3 Replies

5. SCO

Xenix Problems - No space on dev 1/40

Hello - I'm a newbie to these forums. Please excuse me if I am posting in the wrong area. My dilemma. The HD on our ancient Xenix system apparently is full. I receive the "no space on dev 1/40" prompt. This occurred after I attempted to purge some unwanted files. This system runs our small... (1 Reply)
Discussion started by: gmbrickley
1 Replies

6. UNIX for Advanced & Expert Users

adding additional drive to sco the is xenix

I am taking an old xenix drive and installing it in a recent SCO Build Server. I have gone through the process of running mkdev hd twice since the drive is a SCSI then proceed to run mkdev fs and when I attempt to add one of the shown partitions I get the following: fsck: cannot determine... (1 Reply)
Discussion started by: justenglabs
1 Replies

7. Linux

kernel 2.6.8-2-386 > 2.6.16 ???

Is there anything I should know about kernel versions and how they are numbered? I'm trying to compile ivtv drivers. When I run make, the first check is the kernel version. uname -r shows my kernel as 2.6.8-2-386, but I get the error: ivtv-0.6.0 does NOT support kernels > 2.6.16! Is this... (1 Reply)
Discussion started by: System Shock
1 Replies

8. SCO

Help! Playing with Xenix!

Hey everyone! I'm trying to retrieve old files from my Xenix computers. So the option I've now come down to is to load up a second harddrive and do a doscp of my tar'd backup file. Now, How do I go about this? I am not a unix user myself so I'm not quite sure. I need help! I have a VERY short... (1 Reply)
Discussion started by: Slaughter
1 Replies

9. UNIX for Dummies Questions & Answers

Modem problems on SCO Xenix

Randomly receive the following message: "Can not open line tty1a device busy error 16" and "/etc/getty/t60 tty1a" What is causing this error message ? (1 Reply)
Discussion started by: jbartok
1 Replies

10. HP-UX

9-track dinosaur

We just went from HP-UX 10.20 to 11.00. All the bugs are out, except for a small detail...the old 9-track isn't working. We receive large amounts of data on reel-to-reel so I kinda need it fixed. In the meantime, I'm trying to see if they can send me a DAT tape instead. I'm pretty sure the drive... (8 Replies)
Discussion started by: ncmurf00
8 Replies
Login or Register to Ask a Question
DICT_LOOKUP(1)															    DICT_LOOKUP(1)

NAME
dict_lookup - DICT Protocol Client SYNOPSIS
dict_lookuop [options] DESCRIPTION
dict_lookup reads X selection, then open terminal emulator and run dict client in it allowing user to view content using pager. It makes sense to configure launching dict_lookup on a keyboard shortcut in the window manager. OPTIONS
-h display help message. -x x X coordinate of terminal emulator. -x Y Y coordinate of terminal emulator. -s WxH width and height of terminal emulator separated by 'x'. -q query query, if it is specified, X selection is not read. ENVIRONMENT
dict_lookup recognizes the following environment variables. The default value is specified in square brackets. D_AWK_PROG AWK interpreter to use. [awk] D_XCLIP_PROG xclip application. [xclip] D_XTERM_PROG xterm or equivalent terminal emulator. [xterm] D_UTF8_LOCALE UTF-8 locale. [first available UTF-8 locale on system] D_DICT_PROG Dictionary client program. [dict] D_DICT_SERVER Option for dictionary client specifying the server. [-h dict.org] D_DICT_PORT Option for dictionary client specifying the port. [-p 2628] D_DICT_DB_OPT Option for dictionary client specifying the database. [-d foldoc] D_XTERM_CLASS Option for terminal emulator specifying the class. [-class XTerm] D_XTERM_NAME Option for terminal emulator specifying the name. [-name xterm_dict] D_XTERM_TITLE Option for terminal emulator specifying the title. [-title dict_lookup] D_TEXT_WIDTH Program calculating text width for given text. [cyrillic_text_width] cyrillic_text_width doesn't work correctly for Japanese, Korean, Chinese and some other languages. D_TERM_X Terminal emulator X coordinate. [+200] D_TERM_Y Terminal emulator Y coordinate. [+200] D_TERM_H Terminal emulator height. [+40] D_PAGER Pager. [less -R] SEE ALSO
dict(1), less(1), xterm(1), dictd(8), http://www.dict.org, RFC 2229 9 January 2011 DICT_LOOKUP(1)