I shutdown my sco 5.0.7 machine about a month and a half ago and upon bringing it back up got the following kernel panic:
Panic: k_trap - Kernel mode trap type0x0000000E
Unable to freeze processor 2, proceeding....
Cannot dump ?????? pages (I don't remember how many pages it was)
Dump not completed
Safe to power off
or
Press any key to reboot
After pressing enter to reboot the system comes up fine. I had to shutdown again last week and got the same kernel panic but was able to bring the system up by rebooting after the panic.
I'm only getting the panic when I shut it down and boot it back up and after rebooting from the panic everything is fine. The first time it happened I thought it was a fluke but now that it has happened a second time I am worried. Any ideas??
I do have an IRQ conflict but its been there for the past two years and this problem began recently.
Running with RHEL 4.0 ES update 4 (32bit) with the 2.6.11-1226 kernel. During normal operations were enountering a kernel panic which freeze our displays. I hooked up a laptop and captured the following panic from standard output:
NVRM: Xid (0002:00): 13, 0000 01013900 00000039 00000328... (1 Reply)
hi
I've virtualized physical SCO 5.0.6 on ESX 4 according to:
Blog du DS45: HOWTO SCO P2V in the real life
SCO starts with the network, but during shutdown I'm getting this message:
PANIC: k_trap.
My /etc/default/boot:
# cat /etc/default/boot
#ScoAdminInit BOOTMNT {RO RW NO} RO... (4 Replies)
I was following this tutorial on How install the rpmfusion nvidia drivers in Fedora 13:
F13, F12 & F11 Nvidia driver guides - FedoraForum.org
Here's the tutorial:
And this is what I did:
First I executed the following commands:
su
rpm -Uvh ... (0 Replies)
Hi All,
I have installed Solaris 10 on my AMD 64 3000+ system. I was playing with grub commands eeprom and bootadm commands. I screwed my boot-file and now am unable to boot the system. Gets error msg as "panic: cannot open /kernel/amd64/unix". I booted the system is filesafe and tried update the... (2 Replies)
Hi, i'm another question:
I'm a directory /usr/data on my server sco unix 5.0.5:
# du /usr/data
4386948 /usr/data
I'm tried to connect to ftp directory /usr/data to this server and:
PANIC: k_trap - Kernel mode trap type 0x0000000E
Cannot dump 262040 pages to dumpdev hd(1/41):space... (3 Replies)
Guys...
Hows it going???
I have been going through the hardware spec of IBM system p systems.. and here i am confused
for IBM Power 520 Express it says
Processor cores:
One, two or four 64-bit 4.2 GHz POWER6 with AltiVec™ SIMD and Hardware Decimal Floating-Point acceleration
... (1 Reply)
Question is on setting of Physical and Virtual processors for LPARs to make proper use of virtualization capabilities.
Environment is a 8-way p570 with 4 LPARs.
lparVIO1 and lparVIO2:
AIX 5300-04-01
Mode/Type= Shared-SMT/Capped
Minimum Processors= 0.10
Desired Processors= 0.50
Maximum... (1 Reply)
HELP is urgently required,
I run on SCO Unix 3 and this is the panic message that I get every time that I reboot 10U
k_trap - kernel mode trap type 0x0000000E
I have checked the swap already having the following results:
#swap -l
path dev swaplo blocks free... (3 Replies)
processor_sets(4) Kernel Interfaces Manual processor_sets(4)NAME
processor_sets - Collections of processors
DESCRIPTION
A processor set is a collection of processors. When a processor set is first created, it does not contain any processors. You can add
processors to a processor set, remove processors from a processor set, and also destroy the processor set. In addition, you can assign
specific processes to a processor set.
When the system is booted, all its processors are assigned to the default processor set. Each processor in a system can be a member of
only one processor set at one time.
In addition, when you create a process, it is assigned to a processor set. Unless you indicate a specific processor set, a process is
assigned to the default processor set. A process can execute only on an processor that is included in the processor set to which the
process is assigned. If you assign a process to an empty processor set, it will not execute until a processor is assigned to the processor
set or until the process is assigned to another processor set.
Use the pset_create command or the create_pset function to create a processor set. When you first create a processor set, it does not con-
tain any processors.
Use the pset_assign_cpu command or the assign_cpu_to_pset function to assign processors to a specific processor set. When you assign a
processor to a specific processor set, the processor is removed from its current processor set.
Use the pset_destroy command or the destroy_pset function to destroy a processor set. Processors that belong to a destroyed processor set
are assigned to the default processor set.
Use the pset_assign_pid command or the assign_pid_to_pset function to assign a process to a specific processor set. In addition, you can
request that a process has exclusive access to a processor set. If a process has exclusive access to a processor set, no other process is
able to use that processor set. If a process has exclusive access to a processor set, that access will be cleared automatically when the
process exits. Note that if a process is already assigned to a processor set, a request for exclusive access to that processor set will be
denied.
Use the pset_info command to display the status of each processor set on the system as well as the status of each processor.
You must be root to create and destroy processor sets and to assign a processor to a processor set. Processor set creation and destruction
and processor assignments to processor sets are logged in the /var/adm/wtmp file.
FILES
/var/adm/wtmp
RELATED INFORMATION
Commands: pset_create(1), pset_destroy(1), pset_info(1), pset_assign_pid(1), pset_assign_cpu(1), runon(1), psrinfo(1), psradm(8)
Functions: assign_pid_to_pset(3), assign_cpu_to_pset(3), create_pset(3), destroy_pset(3) delim off
processor_sets(4)