Hi,
Im installing sco openserver 5 (OpenServer-5.0.7Hw-10Jun05_1800.iso) on a vmware server 1.0.4.
Installation is ok but on when x server is loading i just can login, mouse does not move and most of keyboard cases do not respond.
I choose usb mouse + french keyboard while installating, should i... (1 Reply)
Hi
I am trying to install NIC FastNic 10/100 PCI Ethernet driver into PCI# 3 of the GA-SIML Rev 1.0 Motherboard on 1GB Hard-disk driveI have following the instruction on the CD-Disk and when I added NIC by netconfig and I do not know what is the following question:
PCI BUS#
DEVICE#... (3 Replies)
Even though IBM states that the x3500 server is Openserver 6.x compatible, it is still a bit of a trick to install SCO Openserver 6 to the machine because the standard method of installing the BTLD required to install the OS requires that the driver be written to a floppy which doesn't exist on... (3 Replies)
I have just been made responsible for setting up Apache on our office SCO
box. I have searched the internet, but
haven't found any details that I can make
sense of. I'm unfamiliar with Unix and would appreciate any help members of
the forum have to offer. (1 Reply)
Hello all,
I'm trying to install SCO openserver 5 on a 2.5 Gig hard drive, and I tried fdisk and a low-level format of the drive. When I insert the boot diskette all seems fine, and it asks me to set the cd-rom and it sees it and reads from it. Well, I'm thinking all is well until right after I... (1 Reply)
UBT(4) BSD Kernel Interfaces Manual UBT(4)NAME
ubt -- USB Bluetooth driver
SYNOPSIS
ubt* at uhub? port ? configuration ? interface ?
DESCRIPTION
The ubt driver provides support for USB Bluetooth dongles to the Bluetooth protocol stack.
USB Bluetooth dongles provide two interfaces, both of which the ubt driver claims. The second interface is used for Isochronous data and
will have several alternate configurations regarding bandwidth consumption, which can be set using the hw.ubtN.config sysctl(8) variable.
The number of alternate configurations is indicated by the value in the hw.ubtN.alt_config variable, and the isoc frame size for the current
configuration is shown in the hw.ubtN.sco_rxsize and hw.ubtN.sco_txsize variables.
By default, configuration 0 is selected, which means that no bandwidth is used on the Isochronous interface and no SCO data can be sent.
Consult the Bluetooth USB specification at https://www.bluetooth.org/ for complete instructions on setting bandwidth consumption. The fol-
lowing extract may be useful as a general guidance though details may differ between manufacturers.
0 No active voice channels
1 One voice channel with 8-bit encoding
2 Two voice channels with 8-bit encoding, or one voice channel with 16-bit encoding.
3 Three voice channels with 8-bit encoding
4 Two voice channels with 16-bit encoding
5 Three voice channels with 16-bit encoding
SEE ALSO bluetooth(4), uhub(4), sysctl(8)HISTORY
This ubt device driver was originally a character device written by David Sainty and Lennart Augustsson. It was rewritten to support socket
based Bluetooth access for NetBSD 4.0 by Iain Hibbert.
CAVEATS
Isochronous data is seemingly not well supported over USB in the current system and to get SCO working, you may have to calculate the SCO
packet size that the stack will use. This is the sco_mtu value reported by the btconfig(8) command, and when combined with the SCO header (3
bytes) should fit exactly into an integer number of Isochronous data frames where the frame size is indicated by the 'hw.ubtN.sco_txsize'
sysctl variable.
For example: I want one voice channel (which is all that is supported, for now) so am using configuration #2, with a frame length of 17
bytes. This gives possible values of:
(17 * 1) - 3 = 14
(17 * 2) - 3 = 31
(17 * 3) - 3 = 48
(17 * 4) - 3 = 65
(17 * 5) - 3 = 82
etc.
btconfig(8) shows the maximum SCO payload as 64 bytes, so I am using the next smaller size of 48, to minimize the overhead of the 3 header
bytes.
The SCO packet size can be changed using the 'scomtu' option to btconfig(8).
The failure mode is that the USB Bluetooth dongle locks up though generally removal/reinsertion will clear the problem.
BUGS
The Isochronous configuration can only be changed when the device is not marked up.
BSD August 27, 2006 BSD