10 More Discussions You Might Find Interesting
1. SCO
Hi,
I am really new to the forum and for SCO as well. I have a burning situation here to know how to configure below list of hardware into SCO 5.0.7!!
EQUINOX 990209-1 ELS 16 PORT TERMINAL SERVER and
Seagate DAT Scorpion 24 - Tape drive ( 12 GB / ) DDS-3 SCSI
Can Any One Please Help Me... (11 Replies)
Discussion started by: Kanthi Kiran
11 Replies
2. Solaris
Hi everybody,
I have a very strange problem ; if somebody could help me it would be very kind. I'll try to explain my problem.
I have 2 unix machines absolutely identical running solaris 9.
For network reasons I need to change the IP address of the 2 machines.
I proceed exactly the same on the... (11 Replies)
Discussion started by: aribault
11 Replies
3. Solaris
Hi
I have installed Solaris 5.10 on Intel x86 machine (standalone).
I want to access internet through solaris. How should I configure the network? Is static IP or DHCP advisable? (5 Replies)
Discussion started by: johnl
5 Replies
4. UNIX for Dummies Questions & Answers
I am using solaris 10, my internet works alright but each time i reboot i keep loosing my connection. I will have to use the
ifconfig iprb0 192.168.1.xx netmask 255.255.255.0 up and
Route add default 192.168.1.xxx command to gain back my internet.
I know there is a better way of addressing... (1 Reply)
Discussion started by: seyiisq
1 Replies
5. SCO
I have a SCO 5.07 Server and I am trying to get it on my network. I have edited the /etc/hosts file and /etc/rc2.d/s99route . I has connectivity on the NIC card but not sure if I am forgetting another file. Thanks! (2 Replies)
Discussion started by: andrewd
2 Replies
6. SCO
Hello Guys,
We have an old PC running on SCO Unix V. Is there any sites where i can get manual/procedures on how to install and configure Network. Thanks (2 Replies)
Discussion started by: nrcuevas
2 Replies
7. Solaris
hi again...
i configured my network settings sometiime ago using the sys-unconfig command.the active link was rtls0.
there was some problem with the network so i changed the ISP. now when im trying to reconfigure the system wit sys-unconfig, it tries to configure the network on rtls1 (and shows... (1 Reply)
Discussion started by: strider
1 Replies
8. IP Networking
Hi guys,
I have set up multiple virtual FTP servers on a server through one physical NIC. I believe there are to ways; setting logical or alias ip's. I would like to know what is the difference between setting up a logical ip or setting up an alias ip to a physical network interface? Some links to... (5 Replies)
Discussion started by: zaff
5 Replies
9. UNIX for Dummies Questions & Answers
Hi,
I'm trying to configure SCO's internet manager for access to
the internet. However, when I start the config program, my desktop turns black & white (unless I minimize communicator's window -- then it turns back to normal).
I type in the user id and password and it looks as if the... (1 Reply)
Discussion started by: gseyforth
1 Replies
10. HP-UX
Hi,
I have installed a HP-UX B.11.00 U 9000/800 Server in one of the domain. And I'm also able to telnet/ping into this server from systems in the same domain.
But I'm not able to telnet/ping into this server from a different domain.
So, what shoud need to do to achieve this... (6 Replies)
Discussion started by: S.Vishwanath
6 Replies
BTSCO(4) BSD Kernel Interfaces Manual BTSCO(4)
NAME
btsco -- Bluetooth SCO Audio
SYNOPSIS
btsco* at bthub?
audio* at audiobus?
DESCRIPTION
The btsco driver provides support for Bluetooth SCO Audio devices through the audio(4) driver.
The btsco driver must be configured at run time with the btdevctl(8) program. The following properties are used by the btsco driver during
autoconfiguration:
local-bdaddr
Local device address.
remote-bdaddr
Remote device address.
service-name
The btsco driver matches the 'HF' and 'HSET' services. For the 'HF' service, the btsco device will, on open(2), listen for incom-
ing connections from the remote device. Otherwise, btsco will attempt to initiate a connection to the remote device.
rfcomm-channel
This integer value is not used directly, but will be stored and passed via the BTSCO_INFO ioctl as below:
SCO connections require a baseband connection between the two devices before they can be created. The btsco driver does not create this, but
can provide information to facilitate an application setting up a control channel prior to use, via the BTSCO_INFO ioctl(2) call on the mixer
device, which returns a btsco_info structure as follows:
#include <dev/bluetooth/btsco.h>
struct btsco_info {
bdaddr_t laddr; /* controller bdaddr */
bdaddr_t raddr; /* headset bdaddr */
uint8_t channel; /* RFCOMM channel */
int vgs; /* mixer index speaker */
int vgm; /* mixer index mic */
};
#define BTSCO_INFO _IOR('b', 16, struct btsco_info)
The btsco driver can be configured to act in Connect or Listen mode. In Connect mode, the btsco driver will initiate a connection to the
remote device on an open(2) call, whereas in Listen mode, open(2) will block until the remote device initiates the connection.
SEE ALSO
bthset(1), ioctl(2), audio(4), bluetooth(4), bthub(4), btdevctl(8)
HISTORY
The btsco driver was written for NetBSD 4.0 by Iain Hibbert under the sponsorship of Itronix, Inc.
BUGS
btsco takes no notice of the HCI Voice Setting in the Bluetooth controller, and this must be 0x0060 (the default) as alternate values are
currently unsupported.
BSD
October 4, 2006 BSD