10 More Discussions You Might Find Interesting
1. Linux
I have created a bridge with nmcli between eth0 and wlan0
I use this procedure
sudo nmcli con add ifname br0 type bridge con-name br0
sudo nmcli con add type bridge-slave ifname eth0 master br0
sudo nmcli con add type bridge-slave ifname wlan0 master br0
sudo nmcli con modify br0... (1 Reply)
Discussion started by: Linusolaradm1
1 Replies
2. UNIX for Advanced & Expert Users
Hi,
I have installed RHEL4 using vmware workstation..
Host OS: Windows XP
Guest OS: RHEL4
Pls refer step 17 & 18 in below link...
ORACLE-BASE - Red Hat Enterprise Linux 4 and Centos 4 Installation
1) If i choose to assign IP automatically (using DHCP) means, i am able to connect RHEL4... (3 Replies)
Discussion started by: thomasraj87
3 Replies
3. Red Hat
Hi All,
Could anyone please help to resolve the below problem.
I installed RHEL5.5 in my desktop.But when i try to activate the ethernet connection then it gives me the error.
I spent 2 days for the above and go through with several suggestion found by googling. But no luck.
... (0 Replies)
Discussion started by: Tanmoy
0 Replies
4. Linux
Assalam o Alaikum!
After configuring and starting service of samba, when I access shared folder from windows XP it gives this error " Network Route was not found".
My server IP 192.168.1.252, client is on same network.
selinux is disabled
smb,conf:
workgroup = WORKGROUP
server string =... (2 Replies)
Discussion started by: ukengr
2 Replies
5. Solaris
Please , I have a problem
I have add a statis route on Solaris 10, but after this, the network interface of Server was Offline.
The system is in cluster mode (3.2)
route add -net 10.10.1.128 -netmask 255.255.255.128 10.10.1.51
-------------------
lo0:... (1 Reply)
Discussion started by: Ruggero
1 Replies
6. Solaris
Hey Guys:
I am trying to add a route for assign a network interface to the traffic to/from a specific net, but allways to get the same system message : network is unreacheable
root@ColectorDMSCNT # route add net 200.44.46.0/24 161.196.84.196 1
add net 200.44.46.0/24: gateway... (2 Replies)
Discussion started by: aggadtech08
2 Replies
7. Solaris
Hi there,
I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far:
# route add... (2 Replies)
Discussion started by: sreiniche
2 Replies
8. Solaris
Hi All,
yesterday I was trying to add a network route to my solaris 8 host using 'route add'. Everytime I tried, I kept getting the response 'network is unreachable'.
I was trying all kinds of different methods, however I eventually got it to work after bouncing the interface that I was... (2 Replies)
Discussion started by: badoshi
2 Replies
9. Shell Programming and Scripting
Hello all :)
I am new to scripting. I need somebody to help me write a script that can edit the files.
For eg: if i say ./script <ipadd> <hostname>
then it should change the ipaddress and hostname in the following files:
1. /etc/hosts
2. /etc/sysconfig/network
3.... (1 Reply)
Discussion started by: Shaikjaveed
1 Replies
10. IP Networking
Hi there guys!
I have a small task that I have to accomplish, but I don't seem to be able to do that.
I have a server that I don't have physical access to, and I mostly control it with webmin. The server is running 2 websites. Both of these websites have their own domains that are linked to... (1 Reply)
Discussion started by: D-Lexy
1 Replies
ROUTE(8) System Manager's Manual ROUTE(8)
NAME
route - manually manipulate the routing tables
SYNOPSIS
/sbin/route [ -f ] [ -n ] [ command args ]
DESCRIPTION
Route is a program used to manually manipulate the network routing tables. It normally is not needed, as the system routing table manage-
ment daemon, routed(8), should tend to this task.
Route accepts two commands: add, to add a route, and delete, to delete a route.
All commands have the following syntax:
/sbin/route command [ net | host ] destination gateway [ metric ]
where destination is the destination host or network, gateway is the next-hop gateway to which packets should be addressed, and metric is a
count indicating the number of hops to the destination. The metric is required for add commands; it must be zero if the destination is on
a directly-attached network, and nonzero if the route utilizes one or more gateways. If adding a route with metric 0, the gateway given is
the address of this host on the common network, indicating the interface to be used for transmission. Routes to a particular host are dis-
tinguished from those to a network by interpreting the Internet address associated with destination. The optional keywords net and host
force the destination to be interpreted as a network or a host, respectively. Otherwise, if the destination has a ``local address part''
of INADDR_ANY, or if the destination is the symbolic name of a network, then the route is assumed to be to a network; otherwise, it is pre-
sumed to be a route to a host. If the route is to a destination connected via a gateway, the metric should be greater than 0. All sym-
bolic names specified for a destination or gateway are looked up first as a host name using gethostbyname(3N). If this lookup fails, get-
netbyname(3N) is then used to interpret the name as that of a network.
Route uses a raw socket and the SIOCADDRT and SIOCDELRT ioctl's to do its work. As such, only the super-user may modify the routing
tables.
If the -f option is specified, route will ``flush'' the routing tables of all gateway entries. If this is used in conjunction with one of
the commands described above, the tables are flushed prior to the command's application.
The -n option prevents attempts to print host and network names symbolically when reporting actions.
DIAGNOSTICS
``add [ host | network ] %s: gateway %s flags %x''
The specified route is being added to the tables. The values printed are from the routing table entry supplied in the ioctl call. If the
gateway address used was not the primary address of the gateway (the first one returned by gethostbyname), the gateway address is printed
numerically as well as symbolically.
``delete [ host | network ] %s: gateway %s flags %x''
As above, but when deleting an entry.
``%s %s done''
When the -f flag is specified, each routing table entry deleted is indicated with a message of this form.
``Network is unreachable''
An attempt to add a route failed because the gateway listed was not on a directly-connected network. The next-hop gateway must be given.
``not in table''
A delete operation was attempted for an entry which wasn't present in the tables.
``routing table overflow''
An add operation was attempted, but the system was low on resources and was unable to allocate memory to create the new entry.
SEE ALSO
intro(4N), routed(8), XNSrouted(8)
4.2 Berkeley Distribution November 16, 1996 ROUTE(8)