You could check with following command if openssh-clients is installed into your system or not.
Also following may help you to understand about openssh-clients.
Thanks,
R. Singh
Not Installed openssh
Quote:
Originally Posted by Scrutinizer
Have you tested manually? Can you reach the server you are rsync'ing with through ssh?.
Is the firewall allowing this connection?
Have you tried to configure it using wget (https) instead of rsync (ssh)? Perhaps that protocol is allowed?
---
@ravindersingh: /etc/hosts.deny is for incoming connections to service is on the hosts itself.
This, however, is an outbound connection from the host to a server on the Internet.
Port 873 is for legacy insecure rsync, and again for incoming connections. Nobody uses that port anymore. Nowadays rsync is typically used with ssh only, which is the default and which usually is on port 22 (but again, for incoming connections, which is not the case here).
The server behind utm
And access to dns http https ftp ssh
[CODE]
So as you confirmed that openssh-clients is not installed and Scrutinizer has also confirmed that rsync requires this facility, so could please try to install openssh into your system and let us know how it goes. You should be root to install the same you could yum for doing the same too.
NOTE: It is just a suggestion it may be or may not be exact solution, please avoid trying this into a LIVE(Production) environment and try to do this into a NON-PROD environment.
Thanks,
R. Singh
This User Gave Thanks to RavinderSingh13 For This Post:
So as you confirmed that openssh-clients is not installed and Scrutinizer has also confirmed that rsync requires this facility, so could please try to install openssh into your system and let us know how it goes. You should be root to install the same you could yum for doing the same too.
NOTE: It is just a suggestion it may be or may not be exact solution, please avoid trying this into a LIVE(Production) environment and try to do this into a NON-PROD environment.
Thanks,
R. Singh
sorry , I just did not notice
My English is a little weak,
ihave changed ssh the defult port
Can be effective in this error?
thanks
---------- Post updated at 02:34 PM ---------- Previous update was at 01:37 PM ----------
rsync: getaddrinfo: feed.openvas.org 873: Temporary failure in name resolution
Let's try one more step here(I am not *NIX expert but trying to troubleshoot here). Above error may be because of file /etc/resolv.conf, could you please check name servers entry in it and do let us know how it goes then.
Thanks,
R. Singh
This User Gave Thanks to RavinderSingh13 For This Post:
Hello,
Did anyone setup a CentOS7 as a gateway (with squid transparent proxy).
I am trying to do so but not able to setup.
I setup squid , iptables (using it instead of firewalld) and all the necessary IPtables rules but nothing work.
It work previously but access.log of squid not getting... (4 Replies)
Hello,
We are migrating our gateways from CentOS 6 to CentOS 7 and for setting up a transparent proxy using squid and Firewalld i am using below configuration.
#Firewalld configurations
firewall-cmd --permanent --zone=public --add-forward-port=port=80:proto=tcp:toport=3128:toaddr=LAN_IP... (4 Replies)
Hallo to everyone.From sometime i have problems with my asterisk pbx on cent os which is in corosync cluster mode with resource groups.The problem is for time the cluster just swap the active one with the other and the only messages in \var\log\messages is that bond0:link status defenitly down for... (0 Replies)
Hello,
Today, i just updated my Openvas server for latest NVT, portsname and scapdata but after that i am not able to login to my openvas instance.
Below command i fired to get this done.
openvas-nvt-sync
openvas-certdata-sync
openvas-portnames-update
openvas-scapdata-sync... (0 Replies)
I attempted to update Python on my CentOS 5.6 VM and have encountered some issues after then. Initially yum wouldn't work, but I have resolved that.
However, now I am unable to access the Network Configuration section under setup.
When I do select this option I see this at the command line:
... (2 Replies)
I am having a bit of trouble getting my CENTOS 6.5 DNS server to work correctly in our testlab environment. Lab network is 10.8.0.0/24 in which we all access from 10.7.0.0.0/24 && 10.0.0.0/24. Here are my configs:
options {
listen-on port 53 { 127.0.0.1; 10.8.0.19;};
#listen-on-v6 port 53 {... (2 Replies)
Hello,
I am using dual boot of linux, one is ubuntu and the other is one is centos.
I have three NIC's and only one of them connected with cable.
The thing is that when I boot from the ubuntu, it does recognize it and I am connected to the Internet.
When I boot from the centos I am not... (6 Replies)