10 More Discussions You Might Find Interesting
1. Solaris
I'm looking for help with a legacy system.
I have some obsolete equipment connected to an Ultra 60 running Solaris 5.7 with the binary for a 32 bit driver. The driver is rejected by newer versions of solaris, which run 64 bit kernels.
I hope to reverse engineer the driver so that I can... (0 Replies)
Discussion started by: obsoleteStuff
0 Replies
2. Hardware
I've had a scsi hard drive, scsi tape drive, and cd rom working off an adaptec 29160 controller. Everything worked great until a few days ago. I begin getting tar format errors (running sco 5.0.6) on the tape drive and occasionally the entire system would hang up while trying to access data on... (0 Replies)
Discussion started by: powwm
0 Replies
3. Solaris
Hi Gurus,
I need help. Mine is an Ultra 10 machine running on solaris 7. Problem with solaris 7 is, it can no longer recognize IDE disks greater that 10GB. My workaround is ro use an external SCSI disk since it is recognizable with solaris 7. I backup my filesystems (residing on the IDE... (2 Replies)
Discussion started by: domesat
2 Replies
4. SCO
Running into an interesting problem here:
I can add the tape with "mkdev tape" the system appears to see it wwith "hwconfig -hc" however a 'tape status /dev/rStp0' says 'no device found',
checked the configuration files in 'etc' all appear to be correct.
Any suggestion appreciated
Jim (3 Replies)
Discussion started by: jimj1369
3 Replies
5. SCO
Hello,
I'm having some issues with installing SCSI tape drive on SCO 5.0.6
hardware config shows the following adapters
%adapter 0xE800-0xE8FF 10 - type=alad ha=0 bus=0 id=7 fts=sto
%adapter 0x0170-0x0177 15 - type=IDE ctlr=secondary dvr=wd
%adapter - 3 - ... (3 Replies)
Discussion started by: ananth_ak
3 Replies
6. HP-UX
I've got an HP9000 server and I'm trying to hook up a tape drive to it. When I go into "SAM-->Peripheral Devices-->Tape Drives", the tape isn't listed. I then choose to "ADD" a drive, and I get the following error.
I know I need to install the "stape" module, but for some reason even that... (2 Replies)
Discussion started by: quantumdude
2 Replies
7. Solaris
hi-
I just installed a quad gigaswift ethernet scsi card to my sunblade 150. I checked with the docs, and got all of the required drivers on the box. Now, I'm trying to mount an external scsi tape drive with no luck. I set the scsi address on the external drive to 0. Here's what I'm coming... (9 Replies)
Discussion started by: ECBROWN
9 Replies
8. UNIX for Dummies Questions & Answers
When I am trying to read any tape I getthe following message on my screen:
"stp: Error on SCSI tape=0 (ha=0 id=6 lun=0)"
Does anybody know how to solve this problem and what the message means.
I already have rebooted the server and cleaned the heads of the tape unit.
HELP!!!! (1 Reply)
Discussion started by: Andre
1 Replies
9. UNIX for Dummies Questions & Answers
I'm running SCO OS 505 on a Compaq proliant 1600, and my tape drive will just not work. It was working properly and whent to Sh?ts when I tried to get the cd rom working. I have uninstalled any configured tape drive and rebooted and then configured a tape drive and rebooted still nothing. I'm... (4 Replies)
Discussion started by: kikkin
4 Replies
10. UNIX for Dummies Questions & Answers
I do daily backups running a shell script. I use 6 different tapes for each day (monday through saturday).
First of all I insert the tape then run the script and when it finished I eject the tape.
Until today I was doing this with no problem, but now I'm getting this message constantly (even... (4 Replies)
Discussion started by: rrivas
4 Replies
TAPEINFO(1) General Commands Manual TAPEINFO(1)
NAME
tapeinfo - report SCSI tape device info
SYNOPSIS
tapeinfo -f <scsi-generic-device>
DESCRIPTION
The tapeinfo command reads various information from SCSI tape drives that is not generally available via most vendors' tape drivers. It
issues raw commands directly to the tape drive, using either the operating system's SCSI generic device ( e.g. /dev/sg0 on Linux,
/dev/pass0 on FreeBSD) or the raw SCSI I/O ioctl on a tape device on some operating systems.
One good time to use 'tapeinfo' is immediately after a tape i/o operation has failed. On tape drives that support HP's 'tapealert' API,
'tapeinfo' will report a more exact description of what went wrong.
Do be aware that 'tapeinfo' is not a substitute for your operating system's own 'mt' or similar tape driver control program. It is intended
to supplement, not replace, programs like 'mt' that access your operating system's tape driver in order to report or set information.
OPTIONS
The first argument, given following -f , is the SCSI generic device corresponding to your tape drive. Consult your operating system's doc-
umentation for more information (for example, under Linux these are generally start at /dev/sg0 under FreeBSD these start at /dev/pass0).
Under FreeBSD, 'camcontrol devlist' will tell you what SCSI devices you have, along with which 'pass' device controls them. Under Linux,
"cat /proc/scsi/scsi" will tell you what SCSI devices you have.
BUGS AND LIMITATIONS
This program has only been tested on Linux with a limited number of tape drives (HP DDS4, Seagate AIT).
AVAILABILITY
tapeinfo is currently being maintained by Robert Nelson <robertnelson@users.sourceforge.net> as part of the 'mtx' suite of programs. The
'mtx' home page is http://mtx.sourceforge.net and the actual code is currently available there and via SVN from http://source-
forge.net/projects/mtx.
SEE ALSO
mt(1),mtx(1),scsitape(1),scsieject(1),loaderinfo(1)
TAPEINFO1.0 TAPEINFO(1)
Adding Legacy SCSI tape to Ent Rel 6 64