10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
Hi,
Please, i have a history of the state of each node in my data center. an history about the failure of my cluster (UN: node up, DN: node down).
Here is some lines of the history:
08:51:36 UN 127.0.0.1 08:51:36 UN 127.0.0.2 08:51:36 UN 127.0.0.3 08:53:50 DN 127.0.0.1 ... (6 Replies)
Discussion started by: chercheur111
6 Replies
2. Red Hat
Dear members & admins
I have 3 RHEL 5.7 servers. So I decided to upgrade them to latest version. 2 of them successfully upgraded to RHEL 5.11 and last one is the problem.
When I hit rhn_register command server shows following info :
#rhn_register
There was an SSL error: (104, 'Connection... (2 Replies)
Discussion started by: sembii
2 Replies
3. AIX
Setting up HACMP 6.1 on a two node cluster. The other node works fine and can start properly on STABLE state (VGs varied, FS mounted, Service IP aliased). However, the other node is always stuck on ST_JOINING state. Its taking forever and you can't stop the cluster as well or recover from script... (2 Replies)
Discussion started by: depam
2 Replies
4. Solaris
Hi,
Is it possible to have a Solaris cluster of 2 nodes at SITE-A using SVM and creating metaset using say 2 LUNs (on SAN). Then replicating these 2 LUNs to remote site SITE-B via storage based replication and then using these LUNs by importing them as a metaset on a server at SITE-B which is... (0 Replies)
Discussion started by: dn2011
0 Replies
5. UNIX for Advanced & Expert Users
We have 2 node Oracle RAC Cluster. It is running RHEL 5 (2.6.18-92.1.10.el5PAE)
Hardware is HP DL360
We have node eviction issue, Oracle evicts node. It is not very consistent.
Oracle has looked all log files and said this is not Oracle issue but rather system or os issue. Server does not... (7 Replies)
Discussion started by: sanjay92
7 Replies
6. IP Networking
Hi,
I've been searching through out this forum to find the exact message when during the on-going FTP, suddenly the network went down but i cannot find some. Could anyone provide me the exact return codes when FTP failed during FTP or prior to FTP the network went down and you still proceeded to... (3 Replies)
Discussion started by: vibora
3 Replies
7. Solaris
i am using Solaris 8 with Volume manager 3.5 & Sun Cluster 3.0.
after installing all thing, when i put --
#vxdctl -c mode
mode:enabled:cluster inactive
i find a solution is to run--
#opt/VRTSvcs/bin/hastatus -sum
but problem is that i haven't any VRTsvcs package. so how can i get VRTSvcs... (4 Replies)
Discussion started by: ranacse
4 Replies
8. HP-UX
Need help guys!
when running cmrunnode batch i'm getting this error
cmrunnode : Waiting for cluster to... (1 Reply)
Discussion started by: Tris
1 Replies
9. Shell Programming and Scripting
Hello,
Under ksh I have to run a script on one of the nodes of a Solaris 8 cluster which at some time must execute a command on the alternate node:
# rsh <name> "command"
I have to implement this script on all the clusters of my company (a lot of...).
Fortunately, the names of the two nodes... (11 Replies)
Discussion started by: heartwork
11 Replies
10. Linux
Hi,
I have a Redhat Cluster Suite with 2 nodes, using option "Multicast HeartBeating" on clumembd, whith default IP: 225.0.0.11
The cluster member names are:
# grep node /etc/hosts
192.168.100.1 node1
192.168.100.2 node2
My problem is that the Multicast IP is relating to other network... (1 Reply)
Discussion started by: Livio
1 Replies
clsetup(1CL) Sun Cluster Maintenance Commands clsetup(1CL)
NAME
clsetup - configure Sun Cluster interactively
SYNOPSIS
/usr/cluster/bin/clsetup -V
/usr/cluster/bin/clsetup -?
/usr/cluster/bin/clsetup [-f logfile]
DESCRIPTION
The clsetup command provides the following configuration capabilities, depending on what state the cluster is in when you issue the com-
mand. The user must be superuser to run this command.
This command has no short form.
o When you run the clsetup command at post-installation time, the command performs initial setup tasks, such as configuring quorum
devices and resetting the installmode property. If you deselected automatic Quroum Configuration when you created the cluster
using either scinstall or the cluster create command, then you must run the clsetup command immediately after the cluster has
been installed. Ensure that all nodes have joined the cluster before you run the clsetup command and reset the installmode prop-
erty.
If you used automatic quorum configuration when you created the cluster, you do not need to run the clsetup command after clus-
ter installation. The automatic quorum configuration feature also resets the installmode property of the cluster.
You can issue this form of the clsetup command from any node in the cluster.
o When you run the clsetup command during normal cluster operation, the scsetup command provides an interactive, menu-driven util-
ity to perform cluster configuration tasks. The following are some of the cluster components which this utility administers:
o Quorum
o Resource groups
o Data services
o Cluster interconnect
o Device groups and volumes
o Private hostnames
o New nodes
o Other cluster properties
You can issue this form of the clsetup command from any node in the cluster.
o When you run the clsetup command from a node that is in noncluster mode, the clsetup command provides a menu-driven utility for
changing and displaying the private IP address range.
You must reboot all nodes into noncluster mode before you start this form of the clsetup utility.
OPTIONS
The following options are supported:
-?
--help
Prints help information for the command.
-f logfile
--file logfile
Specifies the name of a log file to which commands can be logged. If this option is specified, most command sets generated by clsetup
can br run and logged, or just logged, depending on user responses.
-V
--version
Prints the version of the command set. No command line processing will be performed and the command will not enter into its interactive
menu.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWsczu |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
SEE ALSO
Intro(1CL), cldevicegroup(1CL), clnode(1CL), clquorum(1CL), clreslogicalhostname(1CL), clresourcegroup(1CL), clresourcetype(1CL),
clressharedaddress(1CL), cluster(1CL), cltelemetryattribute(1CL)
Sun Cluster 3.2 5 May 2006 clsetup(1CL)