10 More Discussions You Might Find Interesting
1. Red Hat
Dear All,
I have problem at my server. At /var/log/messages
bonding: bond0: link status definitely down for interface eth1, disabling it
tg3 0000:03:00.1: eth1: Link is up at 100 Mbps, full duplex
tg3 0000:03:00.1: eth1: Flow control is off for TX and off for RX
: tg3 0000:03:00.1: eth1:... (0 Replies)
Discussion started by: mjcount
0 Replies
2. Hardware
Hi
This is a question about Broadcom BCM43225 wifi interface on an Acer Aspire laptop
I just had a fresh install of ubuntu 16.04 on my acer aspire laptop and I am having a difficult issue with my wifi connection. Every time I restart my laptop I get the wifi connection working, but after a... (0 Replies)
Discussion started by: faizlo
0 Replies
3. Linux
So I'm having a problem getting a Broadcom BCM4312 wireless controller to work under the broadcom-wl module
$uname
Linux 3.8.11-200.fc18.x86_64 #1 SMP Wed May 1 19:44:27 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux
lspci -v
05:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g... (2 Replies)
Discussion started by: Skrynesaver
2 Replies
4. Solaris
I'm having the hardest time finding the Broadcom drivers for Solaris. I need an odd ball, 32-bit for Solaris 10. Anyone know where I can find one? (0 Replies)
Discussion started by: Ihatewindows
0 Replies
5. Red Hat
I use lspci and dmesg command and find out that i have ipw2000 wireless card on my laptop. I want to install driver for that but i'm not getting proper driver for that.My linux version is el5 and architecture is i386. (0 Replies)
Discussion started by: amitbharad
0 Replies
6. BSD
Is there a way to configure Broadocom wifi 4312 in a bsd system, FreeBSD or OpenBSD. I will appreciate any kind of help.
Thanks in advance (1 Reply)
Discussion started by: piukeman
1 Replies
7. Solaris
Hi to all,
I've installed Solaris 10 on my workstation but I've some networks problems.My NIC,a Broadcom integrated chipset don't work with solaris.Whit the prtconf command I'm unable to identify the correct chipset's model.And I'm searching hovewer for some drivers but I'm fear that Broadcom... (2 Replies)
Discussion started by: bgf0
2 Replies
8. UNIX for Dummies Questions & Answers
I am trying to re-install this netwrok adapter on a server which has just had the motherboard replaced - so much for fault tolerant. I am running SCO Opensercer 5.0.7
Can anyone tell me the Bus no , device number etc that I need to configure this card?
Thanks in advance
Richard (3 Replies)
Discussion started by: farmacy
3 Replies
9. UNIX for Dummies Questions & Answers
Please, I'm From Argentina, And I Need To Know If The Drivers Of Program Unix, Version 5.01 Is Compatible Whit Drivers Of The Printer Epson Fx-2190
Thanks, And I Hope Yuor Answer. (0 Replies)
Discussion started by: juan alberghina
0 Replies
10. SCO
Hi,
I have my server which has LAN with above model build onboard my Dell Server, I got this driver from SCO Unix website but yet to identify the following option:
1. PCI Slot-
2. Bus-
3. Device-
4. Function-
Would anyone please kindly advice what should the... (0 Replies)
Discussion started by: spiderweb
0 Replies
BCMXCP_USB(8) NUT Manual BCMXCP_USB(8)
NAME
bcmxcp_usb - Experimental driver for UPSes supporting the BCM/XCP protocol over USB
NOTE
This man page only documents the hardware-specific features of the bcmxcp_usb driver. For information about the core driver, see
nutupsdrv(8). This driver is a variant of the serial driver bcmxcp and uses the same core code.
SUPPORTED HARDWARE
This driver should recognize all BCM/XCP-compatible UPSes that are connected via USB. It has been developed and tested on Powerware PW3501
hardware. It also has been tested on PW5110 hardware.
EXTRA ARGUMENTS
This driver supports the following optional settings in the ups.conf(5).
shutdown_delay=delay
The number of seconds that the UPS should wait between receiving the shutdown command and actually shutting off.
DEFAULT VALUES FOR THE EXTRA ARGUMENTS
shutdown_delay =120
INSTANT COMMANDS
This driver supports the following Instant Commands:
shutdown.return
Turn off the load and return when power is back.
shutdown.stayoff
Turn off the load and remain off.
test.battery.start
Start a battery test.
TODO LIST
Report UPS alarm status
BCM/XCP supports reporting a wide range of UPS alarm conditions.
Report UPS statistics informations
BCM/XCP supports reporting of UPS statistics data.
EXPERIMENTAL DRIVER
This driver has been tagged experimental, even if it has been reported to be stable. Thus it is not suitable for production systems and it
is not built by default. This is mainly due to the fact that it is a new driver.
INSTALLATION
This driver is not built by default. You can build it by using "configure --with-usb=yes". Note that it will also install other USB
drivers.
You also need to install manually the hotplug files (libhidups and libhid.usermap), generally in etc/hotplug/usb/, to address the
permission settings problem. Lastly note that the libhidups file must have execution flag set (ie using chmod +x ...).
IMPLEMENTATION
bcmxcp_usb only supports 1 UPS at this time. You can put the "auto" value for port in ups.conf, i.e.:
[pw3105]
driver = bcmxcp_usb
port = auto
KNOWN ISSUES AND BUGS
Got EPERM: Operation not permitted upon driver startup""
You have forgotten to install the hotplug files, as explained in the INSTALLATION section above. Don't forget to restart hotplug so that it
applies these changes.
AUTHOR
Tore Orpetveit <tore@orpetveit.net>, Wolfgang Ocker <weo@weo1.de>
SEE ALSO
The core driver:
nutupsdrv(8)
Internet resources:
The NUT (Network UPS Tools) home page: http://www.networkupstools.org/
Network UPS Tools 05/21/2012 BCMXCP_USB(8)