10 More Discussions You Might Find Interesting
1. Red Hat
Dear All,
I have problem at my server. At /var/log/messages
bonding: bond0: link status definitely down for interface eth1, disabling it
tg3 0000:03:00.1: eth1: Link is up at 100 Mbps, full duplex
tg3 0000:03:00.1: eth1: Flow control is off for TX and off for RX
: tg3 0000:03:00.1: eth1:... (0 Replies)
Discussion started by: mjcount
0 Replies
2. Hardware
Hi
This is a question about Broadcom BCM43225 wifi interface on an Acer Aspire laptop
I just had a fresh install of ubuntu 16.04 on my acer aspire laptop and I am having a difficult issue with my wifi connection. Every time I restart my laptop I get the wifi connection working, but after a... (0 Replies)
Discussion started by: faizlo
0 Replies
3. Linux
So I'm having a problem getting a Broadcom BCM4312 wireless controller to work under the broadcom-wl module
$uname
Linux 3.8.11-200.fc18.x86_64 #1 SMP Wed May 1 19:44:27 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux
lspci -v
05:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g... (2 Replies)
Discussion started by: Skrynesaver
2 Replies
4. Solaris
I'm having the hardest time finding the Broadcom drivers for Solaris. I need an odd ball, 32-bit for Solaris 10. Anyone know where I can find one? (0 Replies)
Discussion started by: Ihatewindows
0 Replies
5. Red Hat
I use lspci and dmesg command and find out that i have ipw2000 wireless card on my laptop. I want to install driver for that but i'm not getting proper driver for that.My linux version is el5 and architecture is i386. (0 Replies)
Discussion started by: amitbharad
0 Replies
6. BSD
Is there a way to configure Broadocom wifi 4312 in a bsd system, FreeBSD or OpenBSD. I will appreciate any kind of help.
Thanks in advance (1 Reply)
Discussion started by: piukeman
1 Replies
7. Solaris
Hi to all,
I've installed Solaris 10 on my workstation but I've some networks problems.My NIC,a Broadcom integrated chipset don't work with solaris.Whit the prtconf command I'm unable to identify the correct chipset's model.And I'm searching hovewer for some drivers but I'm fear that Broadcom... (2 Replies)
Discussion started by: bgf0
2 Replies
8. UNIX for Dummies Questions & Answers
I am trying to re-install this netwrok adapter on a server which has just had the motherboard replaced - so much for fault tolerant. I am running SCO Opensercer 5.0.7
Can anyone tell me the Bus no , device number etc that I need to configure this card?
Thanks in advance
Richard (3 Replies)
Discussion started by: farmacy
3 Replies
9. UNIX for Dummies Questions & Answers
Please, I'm From Argentina, And I Need To Know If The Drivers Of Program Unix, Version 5.01 Is Compatible Whit Drivers Of The Printer Epson Fx-2190
Thanks, And I Hope Yuor Answer. (0 Replies)
Discussion started by: juan alberghina
0 Replies
10. SCO
Hi,
I have my server which has LAN with above model build onboard my Dell Server, I got this driver from SCO Unix website but yet to identify the following option:
1. PCI Slot-
2. Bus-
3. Device-
4. Function-
Would anyone please kindly advice what should the... (0 Replies)
Discussion started by: spiderweb
0 Replies
BCMXCP(8) NUT Manual BCMXCP(8)
NAME
bcmxcp - Driver for UPSes supporting the serial BCM/XCP protocol
NOTE
This man page only documents the hardware-specific features of the bcmxcp driver. For information about the core driver, see nutupsdrv(8).
SUPPORTED HARDWARE
This driver should recognize all serial BCM/XCP-compatible UPSes. It has been developed and tested on Powerware PW5115 and PW9120 hardware.
If your UPS has a USB connection, you may also consult the bcmxcp_usb(8) driver documentation.
EXTRA ARGUMENTS
This driver supports the following optional settings in the ups.conf(5).
shutdown_delay=delay
The number of seconds that the UPS should wait between receiving the shutdown command (upsdrvctl shutdown) and actually shutting off.
baud_rate=rate
Communication speed for the UPS. If this is set to 9600, it tries to connect to the UPS at 9600bps. If it fails to communicate, it will
go into baud-hunting. It starts at 1200 and goes up to 19200. If it succeeds, it tell you the speed it connected with. If not included
in the config, it defaults to baud-hunting.
DEFAULT VALUES FOR THE EXTRA ARGUMENTS
o shutdown_delay = 120
o baud_rate = none
INSTANT COMMANDS
This driver supports the following Instant Commands:
shutdown.return
Turn off the load and return when power is back.
shutdown.stayoff
Turn off the load and remain off.
test.battery.start
Start a battery test.
outlet.n.shutdown.return
Turn off the load on outlet n and return when power is back. (n is the outlet number reported by the upsc command)
TODO LIST
Report UPS statistics information
BCM/XCP supports reporting of UPS statistics data.
Change settings
Access the config register to change settings.
BUGS
None known.
AUTHOR
Tore Orpetveit <tore@orpetveit.net>
SEE ALSO
The core driver:
nutupsdrv(8)
The USB BCM/XCP driver:
bcmxcp_usb(8)
Internet resources:
The NUT (Network UPS Tools) home page: http://www.networkupstools.org/
Network UPS Tools 05/21/2012 BCMXCP(8)