10 More Discussions You Might Find Interesting
1. Solaris
I am trying to configuring jumpstart configuration. Please find below sysidcfg configuration file output
bash-3.2# cat sysidcfg
terminal=vt100
network_interface=nxge0 { primary hostname=sun1 ip_address=192.168.11.10 \
protocol_ipv6=no netmask=255.255.255.0 default_route=192.168.11.7}... (5 Replies)
Discussion started by: sb200
5 Replies
2. Shell Programming and Scripting
is it possible to assign value to an array variable from an external file?? if yes then how??
I am using below code but its not working.
#!bin/bash
myarray < file_name
echo ${mayarray} (6 Replies)
Discussion started by: mukulverma2408
6 Replies
3. AIX
Hi,
Trying to setup mediawiki on a system but having problems configuring mysql:
CC=/usr/bin ./configure
checking build system type... powerpc-ibm-aix6.1.0.0
checking host system type... powerpc-ibm-aix6.1.0.0
checking target system type... powerpc-ibm-aix6.1.0.0
checking for a... (9 Replies)
Discussion started by: vpundit
9 Replies
4. Shell Programming and Scripting
Hello,
I am running a bash script under linux which first defines an CA-array like
j=0
num1=120.00
num2=10.00
until
do
CA='echo $num1 + $j*$num2'
j=$
done
within the later awk section of this same script I want to read data from a file. If the value of the second column is... (3 Replies)
Discussion started by: MotAah
3 Replies
5. Solaris
Hello All:
I am trying to configure a J4200 disk array. I am a newbie.
1. I have installed CAM (Common Array Manager).
2. Upgraded the firmware.
3. Registered the array.
a. As per the user guide I should see a sas-domian which I don't.
b. I did not find instructions on how to setup a... (0 Replies)
Discussion started by: pingmeback
0 Replies
6. Infrastructure Monitoring
HI,
I am facing these two errors while configuring snmp can any body guide me.
vi /var/log/snmpd.log
Error opening specified endpoint "udp:161"
Server Exiting with code 1
i also tried
bash-3.00# netstat -a | grep snm
*.snmpd Idle
bash-3.00# lsof -i :161
bash: lsof: command not... (2 Replies)
Discussion started by: nir1785
2 Replies
7. AIX
Hi All
I am new to Apache and AIX and trying to configure Subversion tool in IBM machine with AIX 5.3.Apache is required for client to connect to Subversion Server with http protocol.
1.Installed Apache 2.2.11 and its dependencies via RPM
2.Configured httpd.conf file.
3.Started "httpd"... (1 Reply)
Discussion started by: rajivdp
1 Replies
8. UNIX for Dummies Questions & Answers
Hello there,
I installed Ajaxterm on my Ubuntu 9.04 machine, and it's running ok if I use :
http://localhost:8022/ in my browser it works. The problem is that I wanted to be able to access it from somewhere else through the internet. I've read all the documentation and help that is available for... (1 Reply)
Discussion started by: wosis
1 Replies
9. Solaris
Hi all
Ive got a v440 with an external T3 RAID in a dual bus configuration. I need to add an additional JBOD extension to the disk array via two VDCH cables.
Now, can I do this as the server is live ? Can I just plug the two cables in, switch on the additional extension ? Will this cause... (1 Reply)
Discussion started by: sbk1972
1 Replies
10. IP Networking
Old DG box Aviion PentiumPro running R4.20Mu06 being used to try to recreate Ingres db from backup tapes so machine has not been operational before and some of original files in /etc may have ben overwritten
Unable to get NIC working
Any pointers on how to go about configuring NIC :rolleyes: (0 Replies)
Discussion started by: lindab
0 Replies
MPT(4) BSD Kernel Interfaces Manual MPT(4)
NAME
mpt -- LSI Fusion-MPT SCSI/Fibre Channel driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device scbus
device mpt
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
mpt_load="YES"
DESCRIPTION
The mpt driver provides support for the LSI Logic Fusion-MPT family of SCSI, Fibre Channel and SAS controllers.
HARDWARE
The following controllers are supported by the mpt driver:
o LSI Logic 53c1030, LSI Logic LSI2x320-X (Single and Dual Ultra320 SCSI)
o LSI Logic AS1064, LSI Logic AS1068 (SAS/SATA)
o LSI Logic FC909 (1Gb/s Fibre Channel)
o LSI Logic FC909A (Dual 1Gb/s Fibre Channel)
o LSI Logic FC919, LSI Logic 7102XP-LC (Single 2Gb/s Fibre Channel)
o LSI Logic FC929, LSI Logic FC929X, LSI Logic 7202XP-LC (Dual 2Gb/s Fibre Channel)
o LSI Logic FC949X (Dual 4Gb/s Fibre Channel)
o LSI Logic FC949E, LSI Logic FC949ES (Dual 4Gb/s Fibre Channel PCI-Express)
The Ultra 320 SCSI controller chips supported by the mpt driver can be found onboard on many systems including:
o Dell PowerEdge 1750 thru 2850
o IBM eServer xSeries 335
These systems also contain Integrated Raid Mirroring and Integrated Raid Mirroring Enhanced which this driver also supports.
The SAS controller chips are also present on many new AMD/Opteron based systems, like the Sun 4100. Note that this controller can drive both
SAS and SATA drives or a mix of them at the same time. The Integrated Raid Mirroring available for these controllers is poorly supported at
best.
The Fibre Channel controller chipset are supported by a broad variety of speeds and systems. The Apple Fibre Channel HBA is in fact the
FC949ES card.
This driver also supports target mode for Fibre Channel cards. This support may be enabled by setting the desired role of the core via the
LSI Logic firmware utility that establishes what roles the card can take on - no separate compilation is required.
SEE ALSO
cd(4), ch(4), da(4), pci(4), sa(4), scsi(4), targ(4), mptutil(8), gmultipath(8)
LSI Logic Website, http://www.lsilogic.com/.
HISTORY
The mpt driver first appeared in FreeBSD 4.6.
AUTHORS
The mpt driver was originally written for FreeBSD by Greg Ansley and marginally improved upon by Matt Jacob <mjacob@FreeBSD.org>.
Justin Gibbs <gibbs@FreeBSD.org> and Scott Long <scottl@FreeBSD.org> have made more substantial improvements.
BUGS
BSD
May 13, 2010 BSD
