10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Dear all,
I have a remote CentOS7 server that has two network cards. Each card has four ports and port one of card one was defined with the IP address assigned to the server. So far, so good and it's been working for over a year. We have now got cables sorted out so there are four paths... (4 Replies)
Discussion started by: rbatte1
4 Replies
2. Shell Programming and Scripting
sac_pzs_iv_epoz_hhe__2013.074.14.40.46.0000_2599.365.23.59.59.99999
sac_pzs_iv_epoz_hhn__2013.074.14.40.46.0000_2599.365.23.59.59.99999
sac_pzs_iv_epoz_hhz__2013.074.14.40.46.0000_2599.365.23.59.59.99999
sac_pzs_iv_haga_hhe__2006.111.00.00.00.0000_2599.365.23.59.59.99999... (3 Replies)
Discussion started by: kristinu
3 Replies
3. Red Hat
I have a RAC setup that was configured before I started at my new company. I would like to reconfigure the network devices and change the names. How complex is this regarding the Oracle RAC environment? Does the Oracle RAC rely on the device name or is it only relying on the IP information?
... (1 Reply)
Discussion started by: s ladd
1 Replies
4. AIX
Hi,
is there any method to check the interface collisions on ethernet NIC in AIX. I know that in Solaris it's netstat -i but I've written that in AIX it doesn't show this.
Thanks®ards,
p (1 Reply)
Discussion started by: pitmod
1 Replies
5. Solaris
hi guys,
is there any way to change the nic link_speed in Solaris 10? now my box is running degraded performance of the link speed as the switch is upgraded from 100m to 1000m.
dladm show-dev
e1000g0 link: up speed: 100 Mbps duplex: full
e1000g1 link: up ... (10 Replies)
Discussion started by: freshmeat
10 Replies
6. UNIX for Advanced & Expert Users
Hi,
Does anyone know how can I determine the maximum capable speed on a network interface card for different OS like HP, Sun, AIX and Linux.
I am aware of the tool "ethtool" which can be used for Linux. Are there any handly commands or /proc files where I can get this info depending on the OS.... (3 Replies)
Discussion started by: devtakh
3 Replies
7. Shell Programming and Scripting
I have file names
m04-npt06-z30-syn.ps
m04-npt06-dp018-8x6smp.vmod
m04-npt06-sr40-syn-dp01-16x12drw.params
m04-npt06-sr40-syn-dp008-16x12drw.params
m04-npt06-sr40-syn-dp008-16x12drw.vmod
m04-npt06-sr40-syn-dp008-16x12drw.bck
m04-npt06-sr40-syn-dp008-16x12drw.exp... (6 Replies)
Discussion started by: kristinu
6 Replies
8. Linux
Hi,
I would like to know how to change the speed of ethernet card in linux? as it is showing auto-neg using mii-tool -v eth0
and my requirement is 100mbps full duplex.
Regards,
Manoj (3 Replies)
Discussion started by: manoj.solaris
3 Replies
9. AIX
I am trying to locate a non IBM PCI Ethernet card that will work with the Model B50 RISC box. Alternatively, I need to find AIX drivers for standard PCI Ethernet NIC's ?. (0 Replies)
Discussion started by: rahe
0 Replies
10. UNIX for Advanced & Expert Users
All,
I have a need to software change the MAC address of a NIC in a Sparc Ultra 10 - I believe there is a command that allows to do this at boot up?
Is it a missing (to me) part of ifconfig ?
If so, what is the syntax?
All replies gratefully received !
Thanks
Andrew (3 Replies)
Discussion started by: wretch
3 Replies