9 More Discussions You Might Find Interesting
1. Solaris
Hi, I am new in Solaris 11. I can't even make the NIC work. Here is the issue:
Any help will be greatly appreciated. (6 Replies)
Discussion started by: aixlover
6 Replies
2. Shell Programming and Scripting
Hi Guys
I am using one configuration file for reading some time out values.The format of the file is
A.Type = Number
A.Val = 2000
B.Type = Number
B.Val = 4000
Now my requirement is I need to write a shell script in Solaris where i need to increase these timeout values by 10 times of... (3 Replies)
Discussion started by: mr_deb
3 Replies
3. Solaris
Hi,
Every time when i boot my system i have to manually issue the following commands.
ifconfig elxl0 plumb 192.168.200.129 netmask 255.255.255.0 up
route add default 192.168.200.1
I need some help so that it should be configured permanently and i wouldn't have to manually issue... (2 Replies)
Discussion started by: malikshahid85
2 Replies
4. Solaris
Hi, anyone has had experience in a static setting an IPv6 interface?, I'm trying accordance with the admin guide (ipv6 network configuration tasks), configure one interface in the server, actually i can do ping to my default gateway and access the Internet in IPv6, the specific point is however,... (3 Replies)
Discussion started by: pabloluja
3 Replies
5. UNIX for Dummies Questions & Answers
Hello All
Please can some one help me to use my USB wireless card D-Link on my laptop
i want to configure it, I am using madriva 2010 my system Acer Aspire 4315
i want to know how to configure it and where to get special driver to download the driver
Please (0 Replies)
Discussion started by: bealoumluka
0 Replies
6. SCO
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies
7. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
8. Solaris
Dears,
i follow this to configure Network interface for my PC
O/S : Unix Sun Solaris
vi /etc/hostname.bge0
and write my ip
vi /etc/netmasks
and write my subnetmask
vi /etc/defautrouter
and write my gatwey
vi /etc/resolv.conf
and write my DNS
after i reboot My Computer ... (3 Replies)
Discussion started by: jenovaux
3 Replies
9. Linux
hi all,
:)
Please let mew know some useful link that has some information about wireless set-up and configuration for Linux FC-8 on laptop.
-regards
Ashvin (2 Replies)
Discussion started by: Ashvin Gaur
2 Replies
IW(8) Linux IW(8)
NAME
iw - show / manipulate wireless devices and their configuration
SYNOPSIS
iw [ OPTIONS ] { help [ command ] | OBJECT COMMAND }
OBJECT := { dev | phy | reg }
OPTIONS := { --version | --debug }
OPTIONS
--version
print version information and exit.
--debug
enable netlink message debugging.
IW - COMMAND SYNTAX
OBJECT
dev <interface name>
- network interface.
phy <phy name>
- wireless hardware device (by name).
phy#<phy index>
- wireless hardware device (by index).
reg - regulatory agent.
COMMAND
Specifies the action to perform on the object. The set of possible actions depends on the object type. iw help will print all supported
commands, while iw help command will print the help for all matching commands.
SEE ALSO
ip(8), crda(8), regdbdump(8), regulatory.bin(5)
http://wireless.kernel.org/en/users/Documentation/iw
iw 7 June 2012 IW(8)