First visit to this forum, hope I've chosen an appropriate place to post this.
I have a Java-based application that uses native C++ libraries (built with g++-4.0) for specialized, computation-intensive routines.
Within the native code, I need to catch exceptions thrown inside called methods and throw a corresponding Java exception back to the JVM. This used to work just fine. But I am performing a rebuild after some time has past, and our platform itself (Debian testing) has had some upgrades (to glibc, etc.). Consequently, the desired functionality seems to be broken. The exceptions are not being caught in the new build.
Note: the same code built and tested on MS Windows platforms works just as expected.
Here is a snippet some of the code that is failing:
Here is the error message that the system gives:
Any input or advice would be terrific.
Matthew
P.S. I now realize that this is a poor choice of forum for my question. If it would be more appropriate, could a moderator please move this to Network Computing Topics > C Programming in the UNIX Environment. I see there is a g++-4.0 thread over there. Sorry.
My desired output is
run:
for this 1
for this 2
for this 3
for this 4
for this 5
for this 1,2
1->2
for this 2,3
2->3
for this 3,4
3->4
for this 4,5
4->5
for this 1,2,3
1->2,3 (2 Replies)
HI,
genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
genunix: WARNING: ce0: fault detected external to device; service degraded
genunix: WARNING: ce0: xcvr addr:0x01 - link down
genunix: NOTICE: ce0: fault cleared external to device; service available
genunix: ... (4 Replies)
Hi
i have replace a NIC card on solaris 10 when i give the following command
ifconfig -a
it just show the lo0 (only loop back with inet 127.0.0.1)
when i give the following command to config the interface,
ifconfig elxl0 plumb
ifconfig: plumb: elxl0: no such interface
please help... (11 Replies)
Hi, i have problems with an installation of Debian i386 505 in a pc. The hardware it is a mother soyo with a chipset via.
When i install the xorg, the installation it`s succesfull, but when i type startx, the pc don`t respond.
I am from Argentina and my English it isn`t good. Sorry. (0 Replies)
Hello, I'm trying to use libcurl multi interface to fetch several data in parallel. I would expect this to be faster than performing repeated fetches using the easy interface, but for some reason I can't obtain any speed up at all: using the multi interface actually turns out to be MUCH slower than... (2 Replies)
hi all,
i have problem with my box,
until now i can't investigate the root cause of my issue at my box.
here the problem.
i have a box as a squid server just forward all request packet from one interface and receive the packet then forward to client at the same interface. but after 5 hours i... (1 Reply)
Hi,
tried to native compile Debian Dialog as ncurses-dev is available.
I am trying native compile Debian Dialog using gcc on Linux embedded router.
What's wrong, as running than make
I get errors.
Mayby this line in the log file is an exaplanation to a problem ?
"
checking if we have... (1 Reply)
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)