Cross target debugging


 
Thread Tools Search this Thread
Top Forums Programming Cross target debugging
# 1  
Old 07-15-2011
Error Cross target debugging

I am trying to setup gdbserver debugging on my i386 target platform and running gdb from x86_64 host.

I always get could not load vsyscal try using file etc.. error.

Is there a clean way to setup a cross target gdb.

PS: I also tried set archi i386 on host side.
# 2  
Old 07-15-2011
What exactly are you doing?
# 3  
Old 07-16-2011
basically i run "gdbserver remote:80 ./test" on an i386 target platform. On host i do gdb test. Then on gdb prompt--
target remote <targetIP:80>
break main
cont

it breaks at main, when i do next to single step i get
0x08048810 in printf@plt ()
Login or Register to Ask a Question

Previous Thread | Next Thread

9 More Discussions You Might Find Interesting

1. UNIX for Beginners Questions & Answers

Debugging Help needed

I am VERY much a neophyte with shell scripting. I am working on the following, "Create a script sends an email message to the user specified on the command line if any of the file systems at more than 60% of capacity. The script should not process special file systems as /proc on the... (2 Replies)
Discussion started by: doghouse308
2 Replies

2. HP-UX

After adding new iscsi target port, still the session state of that target port is showing offline

Hi, I wanted to configure new iscsi port on HPUX system, i added the target port address and configured it, once done, went to array side and searched for that host iqn number , but was nt able to find the same, came to host, then when i ran "iscsiutil -pVS" command it gave me below result ... (0 Replies)
Discussion started by: Vinay Kumar D
0 Replies

3. Shell Programming and Scripting

Debugging functions

So here I have a simple function that I wish to debug. However, I am unable to debug the desired function even with set -o functrace enabled. Before resorting to asking this question, I had managed to find a possible solution that did not produce the desired results, which is located here. How... (5 Replies)
Discussion started by: BrandonD
5 Replies

4. Programming

c++ debugging

hey i have a problem with a switch case in program and the debugger is messy has hell ( we use normal VI and gdb in our schoool to make it more diffiacult) any way i have a problom where for some unknown reason the debugger just skips a switch statment as if it wasent even there the rest... (2 Replies)
Discussion started by: gotenxds
2 Replies

5. Shell Programming and Scripting

script debugging

is there any way you can add a breakpoint in a script so you can stop on it? i have used -xv in my shebang but the script just runs and i want it to stop at a specific point in the script. appreciate any help. (1 Reply)
Discussion started by: npatwardhan
1 Replies

6. Programming

Need some help in debugging the C-Progam.

Hi i want to debug the C program with GDB debugger. I want to debug the program by line by line. I want to debug program like as we debug the program in Turbo-C using the F8. Can any one help me? I know i have to use single stepping. But i don't know how to use it. Any help can be appreciated..... (5 Replies)
Discussion started by: ps_sach
5 Replies

7. Solaris

debugging

when I tried to debug my application i got the following. gdb -v GNU gdb 6.6 file is in C and Xmotiff Languages (gdb) attach 25499 Attaching to process 25499 Retry #1: Retry #2: Retry #3: Retry #4: 0xfea40b68 in ?? () (gdb) where #0 0xfea40b68 in ?? () (0 Replies)
Discussion started by: satish@123
0 Replies

8. Programming

Semaphore debugging

I'm running one multithreaded application, in that one of my thread is waiting infinitely in a semphore. Is there a way to determine, in which semaphore the particular thread is waiting and which thread(s) is holding the semaphore. (5 Replies)
Discussion started by: ptprabu
5 Replies

9. Shell Programming and Scripting

Regarding Debugging

Hi, If we want to debug a shell script, then set -vx has to be included in the begining of the script. Just i want to know what purpose -vx is used. Thanks in advace Sarwan (2 Replies)
Discussion started by: sarwan
2 Replies
Login or Register to Ask a Question