10 More Discussions You Might Find Interesting
1. IP Networking
Hello,
I wanted to setup routing certain traffic (http/s) out via a second (faster) interface, like described in the following docs (may not post urls):
linux-ip.net /html/adv-multi-internet.html
thegeekstuff.com /2014/08/add-route-ip-command/
I already had this working years ago on... (0 Replies)
Discussion started by: hyphan
0 Replies
2. Red Hat
libcurl.so.4: cannot open shared object file: No such file or directory
ERROR: Loading network library (net.so) failed!
Press Q to shut down the server!
http://a1108.hizliresim.com/11/8/17/8183.jpg
What must I do ? :wall: (14 Replies)
Discussion started by: Stark0010
14 Replies
3. IP Networking
Hi,
We currently operate a DHCP Server on Vxworks system.
It seems that the server is functioning only over the boot interface.
While trying to use it on a different interface the DHCP client messages seems to reach the interface but stay without response.
From a... (1 Reply)
Discussion started by: zohara
1 Replies
4. Solaris
HI,
genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
genunix: WARNING: ce0: fault detected external to device; service degraded
genunix: WARNING: ce0: xcvr addr:0x01 - link down
genunix: NOTICE: ce0: fault cleared external to device; service available
genunix: ... (4 Replies)
Discussion started by: sunnybee
4 Replies
5. Debian
Hi, i have problems with an installation of Debian i386 505 in a pc. The hardware it is a mother soyo with a chipset via.
When i install the xorg, the installation it`s succesfull, but when i type startx, the pc don`t respond.
I am from Argentina and my English it isn`t good. Sorry. (0 Replies)
Discussion started by: Kritar
0 Replies
6. AIX
Hello,
I need "devices.common.IBM.ml 1.4.0.0 C F Multi Link Interface Runtime" to be installed on my machine.
I need it for two SAN cards to work correctly.
Where do I get it ?
thanks
Vilius (1 Reply)
Discussion started by: vilius
1 Replies
7. UNIX for Advanced & Expert Users
hi all,
i have problem with my box,
until now i can't investigate the root cause of my issue at my box.
here the problem.
i have a box as a squid server just forward all request packet from one interface and receive the packet then forward to client at the same interface. but after 5 hours i... (1 Reply)
Discussion started by: tindasz
1 Replies
8. UNIX for Dummies Questions & Answers
My system info is show below:-
#uname -a
SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500
and I have two network card as shown below:-
#ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0:... (1 Reply)
Discussion started by: sarifudin
1 Replies
9. AIX
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
Discussion started by: aldowsary
7 Replies
10. UNIX for Advanced & Expert Users
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Discussion started by: sc2005
6 Replies