9 More Discussions You Might Find Interesting
1. AIX
Hello,
All the commands on AIX are running very slow.
Below is few stats but I didn't find any issue in cpu or memory reosurces
vmstat
System configuration: lcpu=4 mem=6144MB ent=1.00
kthr memory page faults cpu
----- -----------... (2 Replies)
Discussion started by: Vishal_dba
2 Replies
2. Infrastructure Monitoring
There is a big problem with the server (VPS based on OpenVZ, CentOS 5, 3GB RAM). The problem is the following. The first 15-20 minutes after starting the server is operating normally, the load average is less than or about 1.0, but then begins to increase sharply% wa, then hovers around 95-99%.... (2 Replies)
Discussion started by: draiphod
2 Replies
3. Solaris
I recently configured a WANBoot server on a Ldom 2.0 running Solaris10u9 with ZFS root. When i start the installation form the client with
Ok Boot net - install ,
it takes at least 20-25 minutes just to download the miniroot on the client .. i read there was a bug on T servers firmware... (2 Replies)
Discussion started by: fugitive
2 Replies
4. Shell Programming and Scripting
HI All,
I am trying to automate my stuff to make 'to-do-easier'.
I am new to shell scripting. I need help to you regarding the below problem.
I have one directory in my server, frequently files will store in that directory. I want to move that files into another server on every 5... (5 Replies)
Discussion started by: ravvamohan
5 Replies
5. UNIX for Dummies Questions & Answers
Hi guyes our linux server is very slow today and load average is more than 16 .I m new in linux request you to kindly help resolving the issue.
Where can i find the log for the cause.
# lsb_release -a
LSB Version: ... (2 Replies)
Discussion started by: pinga123
2 Replies
6. UNIX for Dummies Questions & Answers
Hi,
Following my last post I've mounted the remote server on my local server. However copying files from this mounted server is increadbily slow. If I copy files using rcp it's very fast so I assume there must be a setting somewhere?
Any help appreicated.
Thanks (2 Replies)
Discussion started by: AngryBunny
2 Replies
7. UNIX for Advanced & Expert Users
Hello,
I am using Redhat redhat 4 update 4 kernal 2.6. My server is some time suddenly running slow.
The averge cpu load goes up to 50 to 60. (There is only two CPU and usually, the averge load
is between 1 to 2.5) That time, i see, there are several sessions connected.
Normally, we have... (5 Replies)
Discussion started by: govindts
5 Replies
8. HP-UX
Hi,
Since last week our server become too slow when we try to run application on it. When we run top command, it show as below:
So it's nothing to do with heavy utilization, right? Can you give some opinion on what actually had happended?
Thank you very much... :b: (4 Replies)
Discussion started by: yeazas
4 Replies
9. SCO
Hi,
Wonder is someone can help.
I've got a server SCO_SV 3.2v5.0.7 PentIII that is located at a different site and is running slow and has been for a week. I've been speaking to a third party who say nothing is wrong with it but its still running slow.
The 3rd party advise it could be a... (2 Replies)
Discussion started by: tez
2 Replies
ftpshut(1M) System Administration Commands ftpshut(1M)
NAME
ftpshut - close down the FTP Servers at a given time
SYNOPSIS
ftpshut [-V] [-v] [-l min] [-d min] time [warning-message...]
DESCRIPTION
The ftpshut command provides an automated shutdown procedure that the superuser can use to notify FTP users when the FTP Server is shutting
down.
Ten minutes before shutdown, or immediately if the value of time is less than ten minutes, any new FTP Server connections will be disabled.
You may adjust the shutdown of new FTP Server connections by means of the -l option.
Five minutes before shutdown, or immediately if the value of time is less than five minutes, all current FTP connections will be discon-
nected. You may adjust the shutdown of current FTP connections by means of the -d option.
The ftpshut command creates shutdown message files that the FTP Server uses to determine when to shutdown. Separate shutdown message files
are created in the anonymous and virtual host FTP Server areas, in addition to the system wide shutdown message file. Once the shutdown
occurs, the server continues to refuse connections until the appropriate shutdown message file is removed. This normally is done by using
the ftprestart(1M) command. The location of the shutdown message file is specified by the shutdown capability in the ftpaccess file.
The following magic cookies are available:
%s The time system is going to shut down.
%r The time new connections will be denied.
%d The time current connections will be dropped.
%C The current working directory.
%E The maintainer's email address as defined in the ftpaccess file.
%F The free space in the partition of CWD, in kilobytes.
%L The local host name.
%M The maximum allowed number of users in this class.
%N The current number of users in this class.
%R The remote host name.
%T The local time (form Thu Nov 15 17:12:42 1990).
%U The username given at login time.
OPTIONS
The ftpshut command supports the following options:
-V Display program copyright and version information, then terminate.
-d min The time ahead of shutdown, in minutes, that existing connections will be disconnected upon completion of their current or next
(if idle) FTP request.
-l min The time ahead of shutdown, in minutes, that new connections will be refused.
-v Verbose. Output the pathname of the shutdown message files created.
OPERANDS
The ftpshut command supports the following operands:
time The time at which ftpshut will bring the FTP Servers down. time can have a value of now, which indicates an immedi-
ate shutdown. Alternatively, time can specify a future time in one of two formats: +number or HHMM. The first form
brings the FTP Server down in number minutes. The second brings the FTP Server down at the time of day indicated,
using a 24-hour clock format. When using the absolute time format, you can only specify times between now and
23:59.
warning-message The message to display that warns of the imminent shutdown. The warning-message will be formatted at 70 characters
wide. ftpshut knows the actual string length of the magic cookies. If no warning-message is supplied, the default
message "System shutdown at %s" is used.
EXIT STATUS
The following exit values are returned:
0 Successful completion.
>0 An error occurred.
FILES
/etc/ftpd/ftpaccess
/etc/ftpd/ftpservers
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWftpu |
+-----------------------------+-----------------------------+
|Interface Stability |External |
+-----------------------------+-----------------------------+
SEE ALSO
in.ftpd(1M), ftprestart(1M), shutdown(1M), ftpaccess(4), ftpservers(4), attributes(5)
SunOS 5.10 1 May 2003 ftpshut(1M)