Login or Register to Ask a Question and Join Our Community


Post Here to Contact Site Administrators and Moderators

site down investigation

Login to Discuss or Reply to this Discussion in Our Community

 
Thread Tools Search this Thread
Contact Us Post Here to Contact Site Administrators and Moderators site down investigation
# 1  
Old 06-27-2005
site down investigation
I'm rather new to web site administration so i would greatly appreciate some help.

My site has been going down quite frequently and i cannot figure out why. I'm on a shared server at OLM.net and the site goes down once a day or once every 2-3 days which is quite unacceptable. We are still small and we dont get a lot of traffic. We want to have decent reliability before we start heavily marketing and getting more traffic, however i cant seem to figure out how to get to reliability.

I'm open to any suggestions at this point. If its my host, i'm willing to switch if you can suggest a better one. I also understand that it might be because of the shared server, but i want to know for sure that it is before going dedicated, is it my scripts' fault or the server?

Any advice with this would again be greatly appreciated.
Login or Register to Ask a Question

Previous Thread | Next Thread

8 More Discussions You Might Find Interesting

1. What is on Your Mind?

Is this site for me?

Hello, I am new here and my name is Robert. I was actually looking for a forums website where I can go with questions regarding Linux and embedded Linux applications. I am fairly new (6 months) to the world of Linux and embedded Linux applications and the the learning curve is steep. When I am not... (13 Replies)
Discussion started by: Circuits
13 Replies

2. IP Networking

IPSec Openswan Site to Site VPN - Big Pain

Hi @all, I try to connect 2 LANs with IPSec/Openswan LAN 1: 192.168.0.0/24 LAN 2: 192.168.1.0/24 This is my Config: conn HomeVPN # # Left security gateway, subnet behind it, nexthop toward right. left=192.168.1.29 ... (1 Reply)
Discussion started by: bahnhasser83
1 Replies

3. IP Networking

Does cisco 1921 router support site to site VPNs using IPSec?

Q: "Does Cisco 1921 router support,, act as an endpoint for, site to site VPNs using IPSec? If so, how many? " A: If you get the Cisco 1921/k9 with the security services bundle then it will have built in security features. Cisco, typically includes IP Sec tunnels I believe as part of that... (0 Replies)
Discussion started by: Ayaerlee
0 Replies

4. IP Networking

How to establish site to site vpn - Linux machine and cisco asa?

Hi, I am trying to establish vpn between my linux server and cisco asa at client side. I installed openswan on my cent os. Linux Server eth0 - 182.2.29.10 Gateway - 182.2.29.1 eth1 - 192.9.200.75 I have simple IPtables Like WAN="eth0" LAN="eth1" (0 Replies)
Discussion started by: ashokvpp
0 Replies

5. AIX

AIX Shutdown Investigation

AIX error log (read with the errpt command) /var/adm/wtmp account file (read with the last command) /var/adm/pacct account files (read with the lastcomm command) AIX console log (read with the alog -t console -o command) su log file (read with cat /var/adm/sulog) Shell history file (read... (4 Replies)
Discussion started by: prpkrk
4 Replies

6. Linux

Reboot investigation problem

I have a linux server,in this i receive alarm as server has rebooted. When i check uptime of the server it says that the server has rebooted but when i check output of who -b it says that the server rebooted very long back Can some one help what is the issue here. (3 Replies)
Discussion started by: tiwsaj
3 Replies

7. Emergency UNIX and Linux Support

Performance investigation, very high runq-sz %runocc

I've just been handed a hot potato from a colleague who left :(... our client has been complaining about slow performance on one of our servers. I'm not very experienced in investigating performance issues so I hoping someone will be so kind to provide some guidance Here is an overview of the... (8 Replies)
Discussion started by: Solarius
8 Replies

8. IP Networking

port access to site to site VPN

Setup a site to site VPN between two cisco routers. One of the site locations is unable to access ports such as https://example.com:9001 How do I let them go into port 9001? They can ssh, ftp, telnet and everything else. Is this a VPN issue or ACL access issue? I put permit ip host... (0 Replies)
Discussion started by: photon
0 Replies
Login or Register to Ask a Question

LEARN ABOUT ULTRIX

lockd

lockd(8c)																 lockd(8c)

Name
       lockd - network lock daemon

Syntax
       /usr/etc/lockd [ -t timeout ] [ -g graceperiod ]

Description
       The  daemon processes lock requests that are either sent locally by the kernel or remotely by another lock daemon.  The NFS locking service
       makes this advisory locking support possible by using the system call and the subroutine.  The daemon forwards  lock  requests  for  remote
       data  to  the  server  site's lock daemon.  The daemon then requests the status monitor daemon, for monitor service.  The reply to the lock
       request is not sent to the kernel until the status daemon and the server site's lock daemon have replied.

       If either the status monitor or server site's lock daemon is unavailable, the reply to a lock request for remote data is delayed until  all
       daemons become available.

       When  a server recovers, it waits for a grace period for all client site daemons to submit reclaim requests.  Client site daemons are noti-
       fied by of the server recovery and promptly resubmit previously granted lock requests.  If a client site's daemon fails	to  secure  previ-
       ously  granted  locks  at  the server site, the daemon sends the signal SIGLOST to all the processes that were previously holding locks and
       cannot reclaim them.

Options
       -t timeout      The daemon uses timeout (in seconds) as the interval instead of the default value  of  15  seconds  to  retransmit  a  lock
		       request to the remote server.

       -g graceperiod  The daemon uses graceperiod (in seconds) as the grace period duration instead of the default value of 45 seconds.

See Also
       fcntl(2), lockf(3), signal(3), statd(8c)

																	 lockd(8c)