The Migration and DVD/CD Sharing Update is recommended for all users. It provides enhanced customization capabilities and improved performance for migration over FireWire, Ethernet and wireless networks.
I'd like to share some experiences and what I found for NIS migration from Solaris 8 NIS to Linux platform.
I'm not an expert for both platforms, it's just when I tested both systems and found something really tricky. That might takes a lot of time for you to find the root cause. So, I think I can... (11 Replies)
Hello,
Running AIX 7.1 7100-00-03-1115, trying to make a mksysb image to a dvd drive using mkdvd. My final command looks like this..
mkdvd -e -V rootvg -R -C /usr1/AIXADMIN/mkcd/cd_fs -I /usr1/AIXADMIN/mkcd/cd_images -M /usr1/AIXADMIN/mkcd/mksysbimage -d /dev/cd0 -Y
When i run this... (3 Replies)
I'm New to AIX / VIOS
We're doing a FC switch cutover on an ibm device, connected via SAN.
How do I tell if one path to my remote disk is lost? (aix lvm)
How do I tell when my link is down on my HBA port?
Appreciate your help, very much! (4 Replies)
Hi all,
i have just migrate my aix 6.1 to 7.1.
After migration my release is: 7100-00-03-1115
now i try to update to 7100-01-00-1140 but i receive lots of BUILD CHECK DATE FAILED on"mcr.rte" and other packets.
+-----------------------------------------------------------------------------+
... (3 Replies)
Hi,
I can not download iso file as it failed after
downloading 1.1 or 1.2 gigs. I tried several
times but each time it failed and the error
messages like "File not found" or "Read error".
My connection is stable (shown 32kbps and 18 hrs
completion time) and I used jdownloader and
flashgot... (10 Replies)
I have T5220 server with DVD drive. I have installed few logical domains in the server and wonder how they can share the DVD drive. I have not seen any mention of that in Sun documentation. (7 Replies)
I have RedHat 9.0 installed on three of my servers (PIII - 233MHz) and want that they share a common IP address so that any request made reaches each of the servers.
Can anyone suggest how should I setup my LAN. I'm new to networking in Linux so please elaborate and would be thankful for a timely... (2 Replies)
IPX_CMD(8) System Manager's Manual IPX_CMD(8)NAME
ipx_cmd - bridge between Novell's SCMD driver and local IPX network
SYNOPSIS
ipx_cmd -A server name [ -l local interface name ]
DESCRIPTION
ipx_cmd moves packets from tapN to server and vice versa. It is something like IPX Tunnel, but it uses Novell Netware 5 server Compatibil-
ity Mode Driver (AKA Migration Agent) on the other end of wire. You must first configure your kernel tapN device with IPX EthernetII frame
and with network number set up on server (you can use kernel autodetection).
OPTIONS -A server name
This is IP name of compatibility mode server. You can use DNS name or dotted quad to specify server address.
-l local interface name
This allows you to specify, which of your IP addresses should be used as IP address of client side of CMD driver. You must configure
your tapN device with hardware address 7E:01:AA:BB:CC:DD, where AA:BB:CC:DD is your IP address in hexa.
EXAMPLE
If you are on server platan.vc.cvut.cz (147.32.240.81) and your migration agent runs on server boris.vc.cvut.cz, you can configure your
system with:
insmod ethertap
ifconfig tap0 hw ether 7E:01:93:20:F0:51 up
ipx_interface add -p tap0 EtherII
ipx_cmd -A boris.vc.cvut.cz -l 147.32.240.81 &
BUGS
This program was written to satisfy my own needs and should be really improved. At least it should configure tap interface itself.
AUTHOR
Petr Vandrovec <vandrove@vc.cvut.cz>
ipx_cmd IPX Utilities IPX_CMD(8)