Troubleshooting Professional Application Serial Numbers
When entering the serial number for any of Apple's Professional Applications, you may receive an alert stating that "The serial number you entered is not valid."
Oracle Linux 6.4 with bash
Question from a beginner
To change permissions using chmod, I can use 2 methods. Since I don't know the terminology, I am calling them Method1 and Method2.
In the below example, both Method1 and Method2 do the same thing. Which one is you favourite method ?
#... (5 Replies)
Hello!
I am working on an application which reads environmental instruments which have serial ports. The application requires a serial port to be present to talk to the device (i.e. /dev/ttyS0 ). In some instances the environmental devices will be 100's of yards away from the computer, so a... (5 Replies)
Hi community,
I've currently working on SUN Server V490 and I'm connecting with a Serial port (I DON'T HAVE ANY IP CONNECTIVITY)...I need to redirect the graphic interface of Oracle with the dbca command; I know a way with an IP Connectivity ( use a X-Server and then setenv DISPLAY... (7 Replies)
Discussion started by: Sunb3
7 Replies
4. Post Here to Contact Site Administrators and Moderators
Hi there! I liked your forum so much! I'm a professional moderator and I would like to moderate your forum or any part of it. If you are interested in this idea, please apply to me on my e-mail. (5 Replies)
Hello
Here i got a problem, i bought new 40GB hard disk today, i made it as Primary Slave, No when i install Solaris, it says disk need fdisk to make solaris partition, but it does not say which disk need partition, i mean i have two disks, how i suppose to know which disk this will partition,... (1 Reply)
solterm(1) IPMI Serial over LAN program solterm(1)NAME
solterm - An IPMI Serial over LAN program
SYNOPSIS
solterm
<connection parms> [-e escape_char] [-notencrypted] [-notauthenticated] [-bitrate (9600|19200|38400|57600|115200)] [-alerts (suc-
ceed|defer|fail)] [-holdoff] [-ack-retries n] [-ack-timeout microseconds] [-v] [-q]
DESCRIPTION
The solterm program allows a user to make a remote serial connection over IPMI. The requires that the remote system support IPMI 2.0
Serial Over LAN.
OPTIONS
<connection parms>
The parameters for the connection depend on the connection type. These are all described in openipmi_conparms (7)
-e escape_char
The character to use to escape, or exit, the program. Entering this chatacter right after a newline is entered causes the program
to go into command mode. A single character after this performs a command. The default escape character is "~" as shown below.
Suppported commands are:
~. Terminate the program
~B Send a serial BREAK over the connection
~F Flush all buffers
~R Assert the Ring Indicator (RI) line
~r Deassert the Ring Indicator (RI) line
~D Assert DCD and DSR lines
~d Deassert DCD and DSR lines
~C Pause the output using CTS
~c Put CTS under BMC control
~? Help on escape commands
~~ Enter the escape character twice to send it.
-notencrypted
Do not encrypt the SOL data going over the connection.
-notauthenticated
Do not do integrity checks on the SOL data going over the connection.
-bitrate
Set the bitrate to the given value. The default is whatever the BMC has set it to.
-alerts
This specifies what to do if a alert that requires a callout occurs on the line.
succeed
specifies that serial/modem alerts are to succeed while SoL is active.
deferred
specifies that serial/modem alerts are to be deferred for the duration of the SoL session.
fail specifies that serial/modem alerts automatically fail during the SoL session. This is the default.
-holdoff
Specifies that CTS, DTR, and DSR are to be deasserted at the start of the SoL session so that the configuration may be modifeid
before the handshake is released.
-v Be more verbose. Maybe specified multiple time for more output.
-q Be less verbose. Maybe specified multiple time for less output.
SEE ALSO openipmi_conparms(7)KNOWN PROBLEMS
None
AUTHOR
Darius Davis <dariusd@users.sourceforge.net>
OpenIPMI 05/13/03 solterm(1)
