Well, guys I saw a question about GOTO for Python.
So this gave me the inspiration to attempt a GOTO function for 'dash', (bash and ksh too).
Machine: MBP OSX 10.14.3, default bash terminal, calling '#!/usr/local/bin/dash'...
This is purely a fun project to see if it is possible in PURE... (3 Replies)
How to create a new mount point with 600GB and add 350 GBexisting mount point
Best if there step that i can follow or execute before i mount or add diskspace IN AIX
Thanks (2 Replies)
Hey all! :)
I'm trying to create a fixed mount point for an usb cardreader.
I've found a script on a raspberry pi forum which does the following:
usb stick is plugged in -> script checks the mount point for data -> script starts copying the files automatically -> script unmounts the... (0 Replies)
Discussion started by: Eomer
0 Replies
4. Post Here to Contact Site Administrators and Moderators
HI Everyone,
I have below source file
AAA|NAME1|ADDRESS1|300.20
BBB|NAME2|ADDRESS2|400.31
CCC|NAME3|ADDRESS3|300.34
I have requirement where I need to sum up fourth field in above fixed width pipe delimited flat file. When I use below code, it gives me value 1001.00
But I am expecting... (1 Reply)
hi,
I would like to ask or is it possible to dump a hex using dd from starting point to end point just like the "xxd -s 512 -l 512 <bin file>"
I know the redirect hexdump -C but i can't figure it out the combination options of dd.
Hope someone can share their knowledge..
Thanks in... (3 Replies)
Hi!
I'm new in these forums and more or less new with Unix. So... here is the question:
does anyone know where is redirected the output of a command when you put >&- after it?
Does it means any standard file descriptor?
Thanks! (2 Replies)
Anyone know of a guide or instructions for Solaris
I got to configure a SBUS HBA to talk to a tape robot.
I have done this on a switch but not point to point.
just going HBA >>>>> TAPE Fibre simple two nodes
Kie (6 Replies)
gnome-calculator(1) User Commands gnome-calculator(1)NAME
gnome-calculator, gcalctool - perform basic, financial, and scientific calculations
SYNOPSIS
gnome-calculator | gcalctool [-a accuracy] [-D] [-E] [-v] [gnome-std-options]
DESCRIPTION
Gnome calculator is a desktop calculator. It has been designed to be used with either the mouse or the keyboard. It is visually similar to
a lot of hand-held calculators.
Calculator has the following modes:
Basic Mode Provides standard calculator functions. You can store numbers in 10 different memory registers, and easily retrieve
and replace the numbers in the memory registers. Basic Mode is the default mode. You can use all of the Basic Mode
functions in each of the other modes.
Financial Mode Provides several complex financial functions.
Scientific Mode Provides many additional mathematical functions, including trigonometric and logical functions. You can also store
your own functions and constants, when you use Scientific Mode.
EXTENDED DESCRIPTION
Some of the calculator keys have menu marks, this indicates that there is a menu associated with that key.
One of the most important things to remember about gnome-calculator is that calculations are performed from left to right, with no arith-
metic precedence. If you need arithmetic precedence, then you should use parentheses.
Internal arithmetic is now down with multi-precision floating point numbers. Accuracy can be adjusted from zero to nine numeric places in
fixed notation, but numbers can be displayed in engineering and scientific notation as well. There is also an option to show or remove
trailing zeroes after the numeric point. The calculator reverts to scientific notation when the number is larger than the display would
allow in fixed notation. In the scientific mode, the base of operation can be changed between binary, octal, decimal and hexidecimal. Num-
bers are initially displayed in fixed notation to nine numeric places, with trailing zeroes removed, in the decimal base.
You can use the Copy and Paste functions in conjunction with the numeric display to store or retrieve characters from the clipboard. You
can also remove the last digit entered, completely clear the displayed entry and totally reset the calculator.
There are ten memory registers. Numbers can be stored or retrieved in these locations, and arithmetic can be performed upon register con-
tents.
Context sensitive help is also available. Control-F1 toggles whether a tooltip is displayed for the item which currently has focus.
On startup, Calculator uses the following configuration resources stored in a GConf database.
Resource: /schemes/apps/gcalctool/accuracy
Values: Accuracy value
Description: The number of digits displayed after the
numeric point. This value must be in the
range 0 to 9.
Resource: /schemes/apps/gcalctool/base
Values: Numeric Base
Description: The initial numeric base. Valid values are
"BIN" (binary), "OCT" (octal), "DEC" (deci-
mal), and "HEX" (hexadecimal).
Resource: /schemes/apps/gcalctool/display
Values: Display mode
Description: The initial display mode. Valid values are
"ENG" (engineering), "FIX" (fixed-point), and
SCI" (scientific).
Resource: /schemes/apps/gcalctool/mode
Values: Mode
Description: The initial calculator mode. Valid values are
"BASIC", "FINANCIAL", and "SCIENTIFIC".
Resource: /schemes/apps/gcalctool/showzeroes
Values: true, false (true)
Description: Whether to show trailing zeroes after the
numeric point in the display value.
Resource: /schemes/apps/gcalctool/showthousands
Values: true, false (false)
Description: Whether fixed numbers in the decimal base are
displayed with thousands separated.
Resource: /schemes/apps/gcalctool/showregisters
Values: true, false (true)
Description: Whether to display the memory register window
when Calculator starts.
Resource: /schemes/apps/gcalctool/trigtype
Values: Trig. type
Description: The initial trigonometric type. Valid values
are "DEG" (degrees), "GRAD" (grads), and
"RAD" (radians).
Any constants or functions that the user defines are also stored in the GConf database.
OPTIONS
The following options are supported:
-a accuracy Specifies the number of digits displayed after the numeric point. This value must be in the range 0 to 9.
-D Enable debug mode.
-E Enable debug mode in the multiple-precision arithmetic package.
-v Show the version number and usage information.
gnome-std-options Standard options available for use with most GNOME applications. See gnome-std-options(5) for more information.
EXAMPLES
Example 1: Launching Calculator
example% gnome-calculator
EXIT STATUS
The following exit values are returned:
0 Application exited successfully
>0 Application exited with failure
FILES
The following files are used by this application:
/usr/bin/gcalctool Executable for Calculator.
/usr/bin/gnome-calculator Symbolic link to gcalctool.
~/.gcalctoolrc User-specific resources for customizing the appearance and color of Calculator.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWgnome-calculator |
+-----------------------------+-----------------------------+
|Interface stability |Volatile |
+-----------------------------+-----------------------------+
SEE ALSO
Calculator Manual
Latest version of the GNOME Desktop User Guide for your platform.
attributes(5), gnome-std-options(5)NOTES
Written by Glynn Foster and Rich Burridge, Sun Microsystems Inc., 2003.
Updated by Matt Keenan, Sun Microsystems Inc., 2006.
SunOS 5.11 12 Sep 2006 gnome-calculator(1)