7 More Discussions You Might Find Interesting
1. HP-UX
I have used ioscan -fnC tape and the system identified the tape drive. what is the command to show a listing of what is on the tape? I have used ls /dev/rmt/rmt0 to no avail. can anyone help?
Thanks in advance (10 Replies)
Discussion started by: Randydog
10 Replies
2. SCO
I've recently been tasked with "refurbishing" an HP Proliant ML370 running SCO 5.0...something. This is primarily used for legacy support and is kept on a shelf for safe keeping. The scope of work includes hardware diagnostics and blowing the dust out.
I have run HP diagnostics on the array,... (1 Reply)
Discussion started by: v1corp
1 Replies
3. Solaris
Hey folks,
Linux admin here, forced to use Opensolaris to try to use ufsdump/ufsrestore to get some data of some old tapes.
I've got Opensolaris 2009.06 on x86 and a Sony SDX-700V.
As a "control" experiment, I booted the system with a Linux live CD and the tape drive worked perfectly.
... (2 Replies)
Discussion started by: eddy_sysad
2 Replies
4. AIX
Hi,
I'm at AIX 5.3.
My EOD program is giving following error while writing to tape:
Can't write output
cpio: Media Surface error
Failed on Shell-script
cd /; cpio -ocB 2 >> /autoline/misc/logs/bk.CopyToTape < /autoline/work/BACKUP.01022 1>/dev/rm0
I have tried with several new tapes,... (2 Replies)
Discussion started by: tayyabq8
2 Replies
5. AIX
I have tape drive in one Lpar. when i saw that time tape is in defined state. After that i deleted the tape drive using the rmdev -R command. Then fired the cfgmgr -v command. But I am not getting the tape drive. Now the drive is even not in defined state also. It is not shown the tape drive. How... (1 Reply)
Discussion started by: pernasivam
1 Replies
6. SCO
Hello everyone,
First, thank you anyone who might be able to help : ) !!
here it is, I am using SCO at my business, and I back up everything to a tape drive. I want to do my cleaning of the drive, and i put in the cartridge to the drive, it recognizes it yet it will not engage the... (5 Replies)
Discussion started by: RichardHeadd
5 Replies
7. UNIX for Dummies Questions & Answers
Hi,
I need to restore my tape backup, when I type "tape status" it gives;
status : ready beginning-of-tape write-protected
soft errors : 0
hard errors : 0
underruns : 3
but... (4 Replies)
Discussion started by: alisevA3
4 Replies
tms(7) Miscellaneous Information Manual tms(7)
NAME
tms - TMSCP magnetic tape interface
SYNOPSIS
For XMI/KDM on Alpha-based systems:
bus xmi0 at iop0 vector xmierror
controller uq0 at xmi? port kdm vector uqintr
device tape tms0 at uq0 drive 0
For MSI Bus: only MIPS-based DECsystem 5500
bus msi0 at ibus? vector msi_isr
controller dssc1 at msi0 msinode 1
device tape tms3 at dssc1 drive 3
For XMI/CI/HSC on Alpha-based systems:
bus xmi0 at iop0 vector xmierror
bus ci0 at xmi? port np vector cimna_isr
controller hsc6 at ci0 cinode 6
device tape tms3 at hsc6 drive 3
For tms devices dual ported between two controllers:
device tape tms2 at * drive 2
DESCRIPTION
The TMSCP driver provides a standard tape drive interface, as described in mtio(7). This is a driver for any controller that adheres to
the Tape Mass Storage Control Protocol (TMSCP). The TMSCP controllers communicate with the host through a packet-oriented protocol termed
the Tape Mass Storage Control Protocol.
Tape Support - Alpha-based systems
TA78, TA79, TA81, TA90, TA90E, TA91
Diagnostics
All diagnostic messages are sent to the error logger subsystem.
FILES
/dev/rmt???
/dev/nrmt???
SEE ALSO
mtio(7), MAKEDEV(8), uerf(8), tapex(8) delim off
tms(7)