6 More Discussions You Might Find Interesting
1. What is on Your Mind?
Hello, I am new here and my name is Robert. I was actually looking for a forums website where I can go with questions regarding Linux and embedded Linux applications. I am fairly new (6 months) to the world of Linux and embedded Linux applications and the the learning curve is steep. When I am not... (13 Replies)
Discussion started by: Circuits
13 Replies
2. IP Networking
Hi @all,
I try to connect 2 LANs with IPSec/Openswan
LAN 1: 192.168.0.0/24
LAN 2: 192.168.1.0/24
This is my Config:
conn HomeVPN # # Left security gateway, subnet behind it, nexthop toward right. left=192.168.1.29 ... (1 Reply)
Discussion started by: bahnhasser83
1 Replies
3. IP Networking
Q: "Does Cisco 1921 router support,, act as an endpoint for, site to site VPNs using IPSec? If so, how many? "
A: If you get the Cisco 1921/k9 with the security services bundle then it will have built in security features. Cisco, typically includes IP Sec tunnels I believe as part of that... (0 Replies)
Discussion started by: Ayaerlee
0 Replies
4. IP Networking
Hi,
I am trying to establish vpn between my linux server and cisco asa at client side.
I installed openswan on my cent os.
Linux Server
eth0 - 182.2.29.10
Gateway - 182.2.29.1
eth1 - 192.9.200.75
I have simple IPtables Like
WAN="eth0"
LAN="eth1" (0 Replies)
Discussion started by: ashokvpp
0 Replies
5. AIX
Using nimadm:
nimadm -j nimadmvg -c sap024 -s spot_6100 -l lpp_6100 -d "hdisk1" -Y
Initializing the NIM master.
Initializing NIM client sap024.
0505-205 nimadm: The level of bos.alt_disk_install.rte installed in SPOT
spot_6100 (6.1.3.4) does not match the NIM master's level (7.1.1.2).... (2 Replies)
Discussion started by: sciacca75
2 Replies
6. IP Networking
Setup a site to site VPN between two cisco routers.
One of the site locations is unable to access ports such as https://example.com:9001
How do I let them go into port 9001?
They can ssh, ftp, telnet and everything else.
Is this a VPN issue or ACL access issue?
I put
permit ip host... (0 Replies)
Discussion started by: photon
0 Replies
Date::Format(3) User Contributed Perl Documentation Date::Format(3)
NAME
Date::Format - Date formating subroutines
SYNOPSIS
use Date::Format;
@lt = localtime(time);
print time2str($template, time);
print strftime($template, @lt);
print time2str($template, time, $zone);
print strftime($template, @lt, $zone);
print ctime(time);
print asctime(@lt);
print ctime(time, $zone);
print asctime(@lt, $zone);
DESCRIPTION
This module provides routines to format dates into ASCII strings. They correspond to the C library routines "strftime" and "ctime".
time2str(TEMPLATE, TIME [, ZONE])
"time2str" converts "TIME" into an ASCII string using the conversion specification given in "TEMPLATE". "ZONE" if given specifies the
zone which the output is required to be in, "ZONE" defaults to your current zone.
strftime(TEMPLATE, TIME [, ZONE])
"strftime" is similar to "time2str" with the exception that the time is passed as an array, such as the array returned by "localtime".
ctime(TIME [, ZONE])
"ctime" calls "time2str" with the given arguments using the conversion specification "%a %b %e %T %Y
"
asctime(TIME [, ZONE])
"asctime" calls "time2str" with the given arguments using the conversion specification "%a %b %e %T %Y
"
MULTI-LANGUAGE SUPPORT
Date::Format is capable of formating into several languages, these are English, French, German and Italian. Changing the language is done
via a static method call, for example
Date::Format->language('German');
will change the language in which all subsequent dates are formatted.
This is only a first pass, I am considering changing this to be
$lang = Date::Language->new('German');
$lang->time2str("%a %b %e %T %Y
", time);
I am open to suggestions on this.
CONVERSION SPECIFICATION
Each conversion specification is replaced by appropriate characters as described in the following list. The appropriate
characters are determined by the LC_TIME category of the program's locale.
%% PERCENT
%a day of the week abbr
%A day of the week
%b month abbr
%B month
%c MM/DD/YY HH:MM:SS
%C ctime format: Sat Nov 19 21:05:57 1994
%d numeric day of the month, with leading zeros (eg 01..31)
%e numeric day of the month, without leading zeros (eg 1..31)
%D MM/DD/YY
%h month abbr
%H hour, 24 hour clock, leading 0's)
%I hour, 12 hour clock, leading 0's)
%j day of the year
%k hour
%l hour, 12 hour clock
%L month number, starting with 1
%m month number, starting with 01
%M minute, leading 0's
%n NEWLINE
%o ornate day of month -- "1st", "2nd", "25th", etc.
%p AM or PM
%P am or pm (Yes %p and %P are backwards :)
%q Quarter number, starting with 1
%r time format: 09:05:57 PM
%R time format: 21:05
%s seconds since the Epoch, UCT
%S seconds, leading 0's
%t TAB
%T time format: 21:05:57
%U week number, Sunday as first day of week
%w day of the week, numerically, Sunday == 0
%W week number, Monday as first day of week
%x date format: 11/19/94
%X time format: 21:05:57
%y year (2 digits)
%Y year (4 digits)
%Z timezone in ascii. eg: PST
%z timezone in format -/+0000
%d, %e, %H, %I, %j, %k, %l, %m, %M, %q, %y and %Y can be output in Roman numerals by prefixing the letter with "O", e.g. %OY will output
the year as roman numerals.
AUTHOR
Graham Barr <gbarr@pobox.com>
COPYRIGHT
Copyright (c) 1995-1999 Graham Barr. All rights reserved. This program is free software; you can redistribute it and/or modify it under the
same terms as Perl itself.
perl v5.8.0 2002-03-07 Date::Format(3)