ENUM IEEE80211_STA_I(9) Internals ENUM IEEE80211_STA_I(9)NAME
enum_ieee80211_sta_info_flags - Stations flags
SYNOPSIS
enum ieee80211_sta_info_flags {
WLAN_STA_AUTH,
WLAN_STA_ASSOC,
WLAN_STA_PS_STA,
WLAN_STA_AUTHORIZED,
WLAN_STA_SHORT_PREAMBLE,
WLAN_STA_ASSOC_AP,
WLAN_STA_WME,
WLAN_STA_WDS,
WLAN_STA_CLEAR_PS_FILT,
WLAN_STA_MFP,
WLAN_STA_SUSPEND,
WLAN_STA_PS_DRIVER,
WLAN_STA_PSPOLL,
WLAN_STA_DISASSOC
};
CONSTANTS
WLAN_STA_AUTH
Station is authenticated.
WLAN_STA_ASSOC
Station is associated.
WLAN_STA_PS_STA
Station is in power-save mode
WLAN_STA_AUTHORIZED
Station is authorized to send/receive traffic. This bit is always checked so needs to be enabled for all stations when virtual port
control is not in use.
WLAN_STA_SHORT_PREAMBLE
Station is capable of receiving short-preamble frames.
WLAN_STA_ASSOC_AP
We're associated to that station, it is an AP.
WLAN_STA_WME
Station is a QoS-STA.
WLAN_STA_WDS
Station is one of our WDS peers.
WLAN_STA_CLEAR_PS_FILT
Clear PS filter in hardware (using the IEEE80211_TX_CTL_CLEAR_PS_FILT control flag) when the next frame to this station is transmitted.
WLAN_STA_MFP
Management frame protection is used with this STA.
WLAN_STA_SUSPEND
Set/cleared during a suspend/resume cycle. Used to deny ADDBA requests (both TX and RX).
WLAN_STA_PS_DRIVER
driver requires keeping this station in power-save mode logically to flush frames that might still be in the queues
WLAN_STA_PSPOLL
Station sent PS-poll while driver was keeping station in power-save mode, reply when the driver unblocks.
WLAN_STA_DISASSOC
Disassociation in progress. This is used to reject TX BA session requests when disassociation is in progress.
DESCRIPTION
These flags are used with struct sta_info's flags member.
AUTHOR
Johannes Berg <johannes@sipsolutions.net>
Author.
COPYRIGHT Kernel Hackers Manual 2.6. July 2010 ENUM IEEE80211_STA_I(9)
Check Out this Related Man Page
ENUM IEEE80211_CONF_(9) The basic mac80211 driver inte ENUM IEEE80211_CONF_(9)NAME
enum_ieee80211_conf_flags - configuration flags
SYNOPSIS
enum ieee80211_conf_flags {
IEEE80211_CONF_MONITOR,
IEEE80211_CONF_PS,
IEEE80211_CONF_IDLE,
IEEE80211_CONF_OFFCHANNEL
};
CONSTANTS
IEEE80211_CONF_MONITOR
there's a monitor interface present -- use this to determine for example whether to calculate timestamps for packets or not, do not use
instead of filter flags!
IEEE80211_CONF_PS
Enable 802.11 power save mode (managed mode only). This is the power save mode defined by IEEE 802.11-2007 section 11.2, meaning that
the hardware still wakes up for beacons, is able to transmit frames and receive the possible acknowledgment frames. Not to be confused
with hardware specific wakeup/sleep states, driver is responsible for that. See the section "Powersave support" for more.
IEEE80211_CONF_IDLE
The device is running, but idle; if the flag is set the driver should be prepared to handle configuration requests but may turn the
device off as much as possible. Typically, this flag will be set when an interface is set UP but not associated or scanning, but it can
also be unset in that case when monitor interfaces are active.
IEEE80211_CONF_OFFCHANNEL
The device is currently not on its main operating channel.
DESCRIPTION
Flags to define PHY configuration options
AUTHOR
Johannes Berg <johannes@sipsolutions.net>
Author.
COPYRIGHT Kernel Hackers Manual 3.10 June 2014 ENUM IEEE80211_CONF_(9)
I'm getting a error on a old SPARC Station 5 system. The HDD I am using in internal 18GB. Everything use to work, and well wont now.
The error I am getting is in bootup. The error is 'Timeout waiting for ARP?RARP packet error'.
Anyone got any idea how I can fix this? I'm not sure... (4 Replies)
Hello all,
A quick question on Sparc Station 5.
Can I use 18GB hard disk with Sparc Station 5 ?. I searched sunsolve documentation. It gives info only upto 4.2 GB for sparcstaton 5.
The OS is SunOS 5.5.1
Thank You, (3 Replies)
I recently picked up a Sparc Station 20, and installed a fresh copy of Solaris 8 on it.
I've been attempting to set it up so it recognizes/is recognized by the rest of my network so I can setup a PPPoE connection.
According to ifconfig -a, I've got an IP address. According to dmesg | grep... (2 Replies)
The problem is that I use this station as a remote computer for an AOI Orbotech machine and in the root of the station there is no memory available and on the refmgr folder on the same station there are 5GB free memory. So if anyone knows how can I free some space and not damaging the root files,... (0 Replies)
This is a very serious post. I am a Cell Technician (Cellular Base Station Tech) who is completely bored because my job has basically evolved into a Field Secretary position. I love working on T1's and troubleshooting equipment outages and so on and so forth but my job has become VERY... (2 Replies)
hi and how are you?
I am tech, i have power station simelator working by HP PC vectra 486T server.
The OS is SCO UNIX version /386 release 3.2. now the system
compleetly faulty(not working).
I decided to replace the pc with new one but in the version.
I would like to get SCO UNIX OS... (2 Replies)
I had to vent somewhere where people would understand.
The site is still driving me mad. I'm at McMurdo Station, Antarctica, and the satellite bandwidth is generally fairly adequate. I actually completed the application Nov 4th in just under 3 hours I believe. But I removed it thinking it was... (7 Replies)
Just created this beta web app for Tidal Stations - Far East and Australasia:
https://www.unix.com/members/1-albums112-picture628.png
I plan to do the entire "world" soon. (0 Replies)