Login or Register to Ask a Question and Join Our Community

Linux and UNIX Man Pages

Linux & Unix Commands - Search Man Pages

smp_rep_exp_route_tbl(8) [suse man page]

SMP_REP_EXP_ROUTE_TBL(8)					     SMP_UTILS						  SMP_REP_EXP_ROUTE_TBL(8)

NAME

       smp_rep_exp_route_tbl - invoke REPORT EXPANDER ROUTE TABLE LIST SMP function

SYNOPSIS

       smp_rep_exp_route_tbl  [--brief]  [--help] [--hex] [--index=IN] [--interface=PARAMS] [--num=NUM] [--phy=ID] [--raw] [--sa=SAS_ADDR] [--ver-
       bose] [--version] SMP_DEVICE[,N]

DESCRIPTION

       Sends a SAS Management Protocol (SMP) REPORT EXPANDER ROUTE TABLE LIST request function	to  a  SMP  target  and  decodes  or  outputs  the
       response. The SMP target is identified by the SMP_DEVICE and the SAS_ADDR. Depending on the interface, the SAS_ADDR may be deduced from the
       SMP_DEVICE.  With one interface there is one SMP_DEVICE per machine so the SMP_DEVICE[,N] syntax is needed to differentiate between HBAs if
       there are multiple present.

OPTIONS

       Mandatory arguments to long options are mandatory for short options as well.

       -b, --brief
	      reduce the decoded response output.

       -h, --help
	      output the usage message then exit.

       -H, --hex
	      output the response in hexadecimal.

       -i, --index=IN
	      IN is the starting routed SAS address index. The default value is 0.

       -I, --interface=PARAMS
	      interface  specific  parameters.	In this case "interface" refers to the path through the operating system to the SMP initiator. See
	      the smp_utils man page for more information.

       -n, --num=NUM
	      maximum number of descriptors fetch (default is 1). Note that maximum SMP frame size is 1032 bytes (including a trailing 4 byte CRC)
	      which may limit the number of descriptors that can be fetched to 62.

       -p, --phy=ID
	      starting phy identifier. ID should be one of 0 (the default), 48 or 96.

       -r, --raw
	      send the response to stdout in binary. All error messages are sent to stderr.

       -s, --sa=SAS_ADDR
	      specifies  the  SAS address of the SMP target device. Typically this is an expander. This option may not be needed if the SMP_DEVICE
	      has the target's SAS address within it. The SAS_ADDR is in decimal but most SAS addresses are shown in hexadecimal. To give a number
	      in hexadecimal either prefix it with '0x' or put a trailing 'h' on it.

       -v, --verbose
	      increase the verbosity of the output. Can be used multiple times

       -V, --version
	      print the version string and then exit.

CONFORMING TO

       The SMP REPORT EXPANDER ROUTE TABLE LIST function was introduced in SAS-2 .

AUTHORS

       Written by Douglas Gilbert.

REPORTING BUGS

       Report bugs to <dgilbert at interlog dot com>.

COPYRIGHT

       Copyright (C) 2007-2008 Douglas Gilbert
       This  software  is distributed under a FreeBSD license. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR-
       POSE.

SEE ALSO

       smp_utils, smp_rep_route_info

smp_utils-0.93							   January 2008 					  SMP_REP_EXP_ROUTE_TBL(8)

Check Out this Related Man Page

SMP_REP_MANUFACTURER(8) 					     SMP_UTILS						   SMP_REP_MANUFACTURER(8)

NAME

       smp_rep_manufacturer - invoke REPORT MANUFACTURER INFORMATION SMP function

SYNOPSIS

       smp_rep_manufacturer [--help] [--hex] [--interface=PARAMS] [--raw] [--sa=SAS_ADDR] [--verbose] [--version] [--zero] SMP_DEVICE[,N]

DESCRIPTION

       Sends a SAS Management Protocol (SMP) REPORT MANUFACTURER INFORMATION function request to a SMP target. The SMP target is identified by the
       SMP_DEVICE and the SAS_ADDR. Depending on the interface, the SAS_ADDR may be deduced from the SMP_DEVICE. The mpt interface uses SMP_DEVICE
       to identify a HBA (an SMP initiator) and needs the additional ,N to differentiate between HBAs if there are multiple present.

OPTIONS

       Mandatory arguments to long options are mandatory for short options as well.

       -h, --help
	      output the usage message then exit.

       -H, --hex
	      output the response (less the CRC field) in hexadecimal.

       -I, --interface=PARAMS
	      interface  specific  parameters.	In this case "interface" refers to the path through the operating system to the SMP initiator. See
	      the smp_utils man page for more information.

       -r, --raw
	      send the response (less the CRC field) to stdout in binary. All error messages are sent to stderr.

       -s, --sa=SAS_ADDR
	      specifies the SAS address of the SMP target device. Typically this is an expander. This option may not be needed if  the	SMP_DEVICE
	      has the target's SAS address within it. The SAS_ADDR is in decimal but most SAS addresses are shown in hexadecimal. To give a number
	      in hexadecimal either prefix it with '0x' or put a trailing 'h' on it.

       -v, --verbose
	      increase the verbosity of the output. Can be used multiple times

       -V, --version
	      print the version string and then exit.

       -z, --zero
	      zero the Allocated Response Length field in the request. This is required for strict SAS-1.1 compliance. However this option  should
	      not be given in SAS-2 and later; if it is given an abridged response may result.

CONFORMING TO

       The  SMP  REPORT  MANUFACTURER function was introduced in SAS-1, with small additions in SAS-1.1 . This function remains unaltered in SAS-2
       and SPL-1.

AUTHORS

       Written by Douglas Gilbert.

REPORTING BUGS

       Report bugs to <dgilbert at interlog dot com>.

COPYRIGHT

       Copyright (C) 2006-2011 Douglas Gilbert
       This software is distributed under a FreeBSD license. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A  PARTICULAR  PUR-
       POSE.

SEE ALSO

       smp_utils, smp_discover(smp_utils)

smp_utils-0.96							     May 2011						   SMP_REP_MANUFACTURER(8)
Man Page