Login or Register to Ask a Question and Join Our Community


UNIX for Dummies Questions & Answers

nic question...

 
Thread Tools Search this Thread
Top Forums UNIX for Dummies Questions & Answers nic question...
# 1  
Old 12-04-2003
nic question...
Hi everybody,
I want to know if there is a command for solaris or linux to have nic answers, like:

register entity
technical contact
an so on, for a domain.

I know I can do that fron the nic's site, but some guy told me there is a command to do that, but I forget it.

I try dig, host, nslookup but it shows me only the resolution of a domain, not the people involve in the registration, or cantacts.


Thanks .
# 2  
Old 12-04-2003
Hi,

The command you're looking for is whois... do whois and the string you're searching... whois domain, whois nic, etc...
# 3  
Old 12-04-2003
Bingo!!! that's it. Thanks a lot. Muchas gracias. Tantte grazie.



-
 
Login or Register to Ask a Question

Previous Thread | Next Thread

9 More Discussions You Might Find Interesting

1. Linux

Add two different subnet public IPs to single NIC or two different NIC on same box

Hello Admins, My ask is how can I add two different subnet IPs to same box with two different gateways? The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware. How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies

2. Red Hat

I want to tune NIC's rps, rfs and xps value. which NIC device should I modify.

Dear All I want tune my NIC's rps, rfs and xps value. In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1). Here is the question? Which device should I modify ? eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0) Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies

3. IP Networking

squid proxy: one NIC for inbound & one NIC for outbound?

I am new in squid proxy. My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)? Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies

4. Solaris

x86 Solaris 10 nic driver added but not attached. NIC is not detected.

I couldn't install my nic in solaris 10. I compiled and added the driver but failed to attach the driver and ifconfig output shows only loopback dev. Please see the following output and tell me whether my nic has been detected and why the driver failed to attach? My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies

5. UNIX for Dummies Questions & Answers

NIC card monitoring traffic question

Folks; I have 2 NIC cards on my SUSE Linux server. One of them was reporting receive errors for a while now it's OK, but i'd like to monitor it. Is there any command i can run to tell me the usage in the past or give me a history of traffic and the speed that going on this specific card? I... (1 Reply)
Discussion started by: Katkota
1 Replies

6. UNIX for Advanced & Expert Users

Question on NIC and ndd command

I have a T2000 server which has 4 e1000g NIC cards How do I configure each of it for 1Gbit full duplex and turnoff autonegotiation. Please assist Thanks (4 Replies)
Discussion started by: Tirmazi
4 Replies

7. HP-UX

how can I determine which NIC card is virtual NIC Card

how can I determine which NIC card is virtual NIC Card which condition can make a decision Does HP UX have Virtual Network Adapter Concept if ,it has where I can Find if I Install Virutal Network Adapter or which command that i can get it or which software can generate thanks (2 Replies)
Discussion started by: alert0919
2 Replies

8. IP Networking

NIC question!

I have eth1 and eth2 NIC in my Ubuntu. Everything works fine. I have two static IP, on XP and Ubuntu. XP - 192.168.0.1, Ubuntu is 192.168.0.2 on eth1, eth2 is set on DHCP. I have Lan on and internet sharing. I share internet over XP. Can somebody explain to me some things: I assume that eth1 is my... (2 Replies)
Discussion started by: salvor_hardin
2 Replies

9. UNIX for Dummies Questions & Answers

NIC driver building question

I'm way confused. I loaded RH 7.1 on an old P-75 Compaq. IT has an EtherExpress pro/100 card in it and I have that attached to the optional port on our firewall with a crossover....I can't seem to get the card to negotiate with the firewall...it's currently 100Meg at Half duplex. I'm at a loss... (3 Replies)
Discussion started by: kwalter
3 Replies
Login or Register to Ask a Question