mclasserase(1) [suse man page]

mclasserase(1) General Commands Manual mclasserase(1)

Name
mclasserase - erase memory cards

Note of warning
This manpage has been automatically generated from mtools's texinfo documentation, and may not be entirely accurate or complete. See the
end of this man page for details.

Description
The mclasserase command is used to wipe memory cards by overwriting it three times: first with 0xff, then with 0x00, then with 0xff again.
The command uses the following syntax:

mclasserase [-d] msdosdrive

MS-DOS drive is optional, if none is specified, use A:. If more than one drive are specified, all but the last are ignored.

Mclasserase accepts the following command line options:

d Stop after each erase cycle, for testing purposes

p Not yet implemented

Mclasserase returns 0 on success or -1 on failure.

See Also
Mtools' texinfo doc

Viewing the texi doc
This manpage has been automatically generated from mtools's texinfo documentation. However, this process is only approximative, and some
items, such as crossreferences, footnotes and indices are lost in this translation process. Indeed, these items have no appropriate repre-
sentation in the manpage format. Moreover, not all information has been translated into the manpage version. Thus I strongly advise you
to use the original texinfo doc. See the end of this manpage for instructions how to view the texinfo doc.

* To generate a printable copy from the texinfo doc, run the following commands:

./configure; make dvi; dvips mtools.dvi

* To generate a html copy, run:

./configure; make html

A premade html can be found at `http://www.gnu.org/software/mtools/manual/mtools.html'

* To generate an info copy (browsable using emacs' info mode), run:

./configure; make info

The texinfo doc looks most pretty when printed or as html. Indeed, in the info version certain examples are difficult to read due to the
quoting conventions used in info.

mtools-4.0.13 28Feb10 mclasserase(1)

Check Out this Related Man Page

mshortname(1)						      General Commands Manual						     mshortname(1)

Name
       mshortname - shows short name of a file

Note of warning
       This  manpage  has been automatically generated from mtools's texinfo documentation, and may not be entirely accurate or complete.  See the
       end of this man page for details.

Description
       The mshortname command is used to display the short name of a file.  Syntax:

       mshortname files

       The shortname is displayed as it is stored in raw format on disk, without any character set conversion.

See Also
       Mtools' texinfo doc

Viewing the texi doc
       This manpage has been automatically generated from mtools's texinfo documentation. However, this process is only  approximative,  and  some
       items, such as crossreferences, footnotes and indices are lost in this translation process.  Indeed, these items have no appropriate repre-
       sentation in the manpage format.  Moreover, not all information has been translated into the manpage version.  Thus I strongly  advise  you
       to use the original texinfo doc.  See the end of this manpage for instructions how to view the texinfo doc.

       *      To generate a printable copy from the texinfo doc, run the following commands:

		     ./configure; make dvi; dvips mtools.dvi

       *      To generate a html copy,	run:

		     ./configure; make html

       A premade html can be found at `http://www.gnu.org/software/mtools/manual/mtools.html'

       *      To generate an info copy (browsable using emacs' info mode), run:

		     ./configure; make info

       The  texinfo  doc looks most pretty when printed or as html.  Indeed, in the info version certain examples are difficult to read due to the
       quoting conventions used in info.

mtools-4.0.18							      09Jan13							     mshortname(1)

Linux and UNIX Man Pages

mclasserase(1) [suse man page]

Check Out this Related Man Page