redhat traceroute6 man page on unix.com

TRACEROUTE(1) General Commands Manual TRACEROUTE(1)

NAME
traceroute - print the route packets take to network host

SYNOPSIS
traceroute [-46FInrRTV] [-f first_ttl] [-p port]
[-m max_hops] [-N concurrent_hops]
[-t tos] [-w timeout] [-q nqueries]
[-S source_addr] [-i interface]
[-g gateway] host [packetlen]
traceroute6 [options]

DESCRIPTION
traceroute tracks the route packets take across a TCP/IP network on their way to a given host. It utilizes the IP protocol's time to live
(TTL) field and attempts to elicit an ICMP TIME_EXCEEDED response from each gateway along the path to the host.

traceroute6 is just another name for the same program, and is equivalent to invoking traceroute with the -6 option.

Tracing with UDP
The default mode of operation is to use UDP packets for path detection. This will send packets of a given size to a range of destination
ports, usually in the high port range, and increment the destination port number for each probe packet sent). Intermediate gateways will
return ICMP time exceeded errors when the packet's TTL reaches zero. When a packet reaches the remote host, and the chosen port is not in
use, the host will return an ICMP port unreachable error. If the port is in use, the probe packet will be delivered to this port, more
likely than not without eliciting a response.

The port range is chosen so that it is rather unlikely that this port will be in use on the remote system.

Tracing in UDP mode does not require super user privileges, as the Linux UDP implementation supports a so-called error queue, through which
ICMP error packets related to a specific port can be delivered to the application.

Tracing with ICMP
In this mode, traceroute sends ICMP echo packets to the destination host, pretty much like the ping utility.

ICMP tracing requires super user privilege, as it needs to open a raw socket to listen for incoming ICMP packets. Non-root users are not
permitted to open such sockets for security reasons.

ICMP traces are currently supported over IPv4 only.

Tracing with TCP
In TCP mode, traceroute will try to connect to the destination host. This causes the kernel to send a SYN packet to the remote host, again
varying the TTL for each probe. The default port number used for TCP probes is 80 (http). When the probe reaches the destination host, it
will either accept the connection (in case there's a service listening on this port), or respond with a TCP RST packet (in case there
isn't).

TCP tracing requires super user privilege, as it needs to open a raw socket to listen for incoming ICMP packets. Non-root users are not
permitted to open such sockets for security reasons.

ICMP traces are currently supported over IPv4 only.

Caveats
Many gateways are configured to limit the rate at which they will send ICMP error packets. Thus, when you run lots of traces in close suc-
cession, an increasing number of gateways may "disappear", with probes timing out instead of eliciting an ICMP response. Rate limiting
often happens at a granularity of 30 to 60 seconds, so do not expect things to work properly if you run more than two or three traces per
minute.

OPTIONS
The only required parameter is the name or IP address of the destination host. This parameter can be followed by the size of the probing
packet sent to that host (40 by default). Varying the size of the packet in conjunction with the -F parameter can be used to obtain infor-
mation about the MTU of individual network hops. This does not apply to TCP, which uses SYN packets to establish a path trace.

Additional options are:

-6, -4 Explicitly force IPv4 or IPv6 traceouting. By default, the program will try to resolve the name given, and choose the appropriate
protocol automatically. If resolving a host name returns both IPv4 and IPv6 addresses, traceroute will use IPv4. Invoking the pro-
gram as traceroute6 is the same as using the -6 option.

-F Set the "Don't Fragment" bit. This tells intermediate routers not to fragment the packet when they find it's too big for a network
hop's MTU.

-f first_ttl
Specifies with what TTL to start. Defaults to 1.

-g gateway
Tells traceroute to add an IP source routing option to the outgoing packet that tells the network to route the packet through the
specified gateway. Not very useful, because most routers have disabled source routing for security reasons.

-I Use ICMP ECHO instead of UDP packets when probing the route. This option is available to the super user only, as normal users do
not have the privileges to create raw sockets.

-i interface
Specifies the interface through which to traceroute should send packets. By default, the interface is selected according to the
routing table.

NOTE: This option changed from previous versions of traceroute! Older versions used -I to specify the interface name.

-m max_hops
Specifies the maximum number of hops traceroute will probe. The default value is 30.

-N concurrent_hops
Specifies the number of probe packets sent out simultaneously. Sending several probes concurrently can speed up traceroute consid-
erably. However, when specifying a number that's too large, the destination host will start to throw away random ICMP responses (if
it implements ICMP rate throttling), and traceroute will be unable to detect the final hope reliably. The default value is 6.

-n Do not try to map IP addresses to host names when displaying them.

-p port
Specifies the UDP destination port base traceroute will use. When sending its UDP probe packets, it will send them to port + hop - 1
for each hop. If there are ports in this range in use on the destination host, traceroute will not be able to identify reliably when
it has reached the destination host (probes will appear to time out). The default port is 33434; you can use -p to change this to a
different value.

-q numqueries
Sets the number of probe packets per hop. The default value is 3.

-r Bypass the normal routing tables and send directly to a host on an attached network. If the host is not on a directly-attached net-
work, an error is returned. This option can be used to ping a local host through an interface that has no route through it.

-R Set the loose source route option on outgoing packets, asking intermediate routers to record their address as the packet passes.
This can be useful if you want to find the address of an intermediate router that has been configured to not respond to traceroute
packets.

This feature hasn't been implemented yet.

-S source_addr
Chooses an alternative source address. Note that you must select the address of one of the interfaces. By default, the address of
the outgoing interface is used.

-T Use TCP instead of UDP packets when probing the route. This option is available to the super user only, as this requires a raw ICMP
socket, which normal users are not permitted to create.

-t tos Set the IP Type of Service (TOS) and Precedence value. Useful values are 16 (low delay) and 8 (high throughput). Note that in order
to use some TOS precendence values, you have to be super user.

-V Print the version and exit.

-w sec Wait for sec seconds before sending the next probe packet.

Note that unlike older traceroute versions, this implementation will transmit several probe packets in parallel, for different hop
values. However, it will never send more than 1 packet per hop value at the same time.

redhat man page for traceroute6