Home Man
Search
Today's Posts
Register

Linux & Unix Commands - Search Man Pages

RedHat 9 (Linux i386) - man page for avmcapictrl (redhat section 8)

AVMCAPICTRL(8)			   Linux System Administration			   AVMCAPICTRL(8)

NAME
       avmcapictrl - Add, reset or remove active AVM cards and load firmware

SYNOPSIS
       avmcapictrl add <portbase> <irq> <type>
       avmcapictrl load <bootcode> [<contrnr> [<protocol>
	   [P2P | <dn1>:<spid1> [<dn2>:<spid2>]]]]
       avmcapictrl reset [contrnr]
       avmcapictrl remove [contrnr]
       avmcapictrl trace [contrnr] [off|short|on|full|shortnodata|nodata]
       avmcapictrl addcard <driver> <portbase> <irq> [ <membase> [ <cardnr> ] ]

DESCRIPTION
       avmcapictrl  is	used  to register active AVM ISA cards kernelcapi system and therewith to
       the isdn system. You need it also to upload the firmware to any active  AVM  card.  If  an
       error occure please also check the kernel error messages by using the command dmesg(8).

COMMANDS
       add <portbase> <irq> <type>
	    is	used  to  add a ISA card to the kernel-capi2.0 system.	The portbase can have the
	    values 0x150, 0x250, 0x300 and 0x340 for the B1 ISA cards, look at the jumper on  the
	    card.  For a T1-ISA (HEMA) card you can select an wide range of ports.
	    irq can be selected from the following values:
	    3, 4, 5, 6, 7, 9, 10, 11, 12 and 15.
	    type can be B1 or T1.

       load <bootcode> [<contrnr> [<protocol>
	    [P2P  | <dn1>:<spid1> [<dn2>:<spid2>]]]] is used to load the firmware to a card boot-
	    code is a t4-file. The actual versions of the t4-files for	the  different	d-channel
	    protocols can be found at ftp://ftp.avm.de/cardware/b1/linux/firmware.
	    You  need  different t4-files for different d channel protocols: b1-1tr6.t4 for 1TR6,
	    b1.t4 for DSS1 and
	    b1-usa.t4 for 5ESS and NI1 (DSS1 is also supported).
	    For M1/M2 PCMCIA cards you need m1-s10.t4 or m1-s4.t4 depending  on  the  handy  type
	    used.
	    contrnr is the number of the controller (card) starting from 1.
	    protocol can be DSS1, CT1, VN3, AUSTEL, 5ESS or NI1.
	    P2P point to point
	    DN1:SPID1 DN2:SPID2 is for the american protocols 5ESS and NI1.

       reset [contrnr]
	    is used to reset a card if loading has failed.  This function only make sence if card
	    is not successfully loaded.
	    contrnr is the number of the controller (card) starting from 1.

       remove [contrnr]
	    is used to remove a card previous added. You can also remove  automatic  added  cards
	    (for example a B1-PCI card).
	    contrnr is the number of the controller (card) starting from 1.

       trace [contrnr] [off|short|on|full|shortnodata|nodata]
	    is	used  to  trace  CAPI2.0 messages. The trace will be done as kernel messages, see
	    dmesg(8).
	    contrnr is the number of the controller (card) starting from 1.
	    off switch traceing off
	    short switch one line per CAPI2.0 message tracing on
	    on | full switch on full decode tracing
	    shortnodata switch on line per CAPI2.0 message tracing on,	but  exclude  DATA_B3_IND
	    and DATA_B3_REQ messages.
	    on | full switch on full decode tracing, but exclude DATA_B3_IND and DATA_B3_REQ mes-
	    sages.

       addcard <driver> <portbase> <irq> [ <membase> [ <cardnr> ] ]
	    is used to add a card, this is more generic than add.
	    driver currently b1isa or t1isa
	    portbase can have the values 0x150, 0x250, 0x300 and 0x340 for the b1isa driver, look
	    at the jumper on the card.	For t1isa driver you can select an wide range of ports.
	    irq can be selected from the following values: 3, 4, 5, 6, 7, 9, 10, 11, 12 and 15.
	    membase memory address if needed by driver
	    cardnr only usefull with driver t1isa

AUTHOR
       Carsten Paeth <calle@calle.in-berlin.de>

SEE ALSO
       ttyI(4), isdnctrl(8), isdninfo(4).  dmesg(8).  syslogd(8).

4th Berkeley Distribution		    2000/01/28				   AVMCAPICTRL(8)


All times are GMT -4. The time now is 10:19 PM.

Unix & Linux Forums Content Copyrightę1993-2018. All Rights Reserved.
UNIX.COM Login
Username:
Password:  
Show Password