mmount(1) [redhat man page]

mmount(1) General Commands Manual mmount(1)

Name
mmount - mount an MSDOS disk

Note of warning
This manpage has been automatically generated from mtools's texinfo documentation, and may not be entirely accurate or complete. See the
end of this man page for details.

Description
The mmount command is used to mount an MS-DOS disk. It is only available on Linux, as it is only useful if the OS kernel allows to config-
ure the disk geometry. Its syntax is:

mmount msdosdrive [mountargs]

Mmount reads the boot sector of an MS-DOS disk, configures the drive geometry, and finally mounts it passing mountargs to mount. If no
mount arguments are specified, the name of the device is used. If the disk is write protected, it is automatically mounted read only.

See Also
Mtools' texinfo doc

Viewing the texi doc
This manpage has been automatically generated from mtools's texinfo documentation. However, this process is only approximative, and some
items, such as crossreferences, footnotes and indices are lost in this translation process. Indeed, these items have no appropriate repre-
sentation in the manpage format. Moreover, not all information has been translated into the manpage version. Thus I strongly advise you
to use the original texinfo doc. See the end of this manpage for instructions how to view the texinfo doc.

* To generate a printable copy from the texinfo doc, run the following commands:

./configure; make dvi; dvips mtools.dvi

* To generate a html copy, run:

./configure; make html

A premade html can be found at: `http://mtools.linux.lu' and also at: `http://www.tux.org/pub/knaff/mtools'

* To generate an info copy (browsable using emacs' info mode), run:

./configure; make info

The texinfo doc looks most pretty when printed or as html. Indeed, in the info version certain examples are difficult to read due to the
quoting conventions used in info.

mtools-3.9.8 02Jun01 mmount(1)

Check Out this Related Man Page

mmd(1)							      General Commands Manual							    mmd(1)

Name
       mmd - make an MSDOS subdirectory

Note of warning
       This  manpage  has been automatically generated from mtools's texinfo documentation, and may not be entirely accurate or complete.  See the
       end of this man page for details.

Description
       The mmd command is used to make an MS-DOS subdirectory. Its syntax is:

       mmd [-D clash_option] msdosdirectory [ msdosdirectories... ]

       Mmd makes a new directory on an MS-DOS filesystem. An error occurs if the directory already exists.

See Also
       Mtools' texinfo doc

Viewing the texi doc
       This manpage has been automatically generated from mtools's texinfo documentation. However, this process is only  approximative,  and  some
       items, such as crossreferences, footnotes and indices are lost in this translation process.  Indeed, these items have no appropriate repre-
       sentation in the manpage format.  Moreover, not all information has been translated into the manpage version.  Thus I strongly  advise  you
       to use the original texinfo doc.  See the end of this manpage for instructions how to view the texinfo doc.

       *      To generate a printable copy from the texinfo doc, run the following commands:

		     ./configure; make dvi; dvips mtools.dvi

       *      To generate a html copy,	run:

		     ./configure; make html

	      A premade html can be found at: `http://mtools.linux.lu' and also at: `http://www.tux.org/pub/knaff/mtools'

       *      To generate an info copy (browsable using emacs' info mode), run:

		     ./configure; make info

       The  texinfo  doc looks most pretty when printed or as html.  Indeed, in the info version certain examples are difficult to read due to the
       quoting conventions used in info.

mtools-3.9.8							      02Jun01								    mmd(1)

Linux and UNIX Man Pages

mmount(1) [redhat man page]

Check Out this Related Man Page