mcd(1) [redhat man page]
mcd(1) General Commands Manual mcd(1) Name mcd - change MSDOS directory Note of warning This manpage has been automatically generated from mtools's texinfo documentation, and may not be entirely accurate or complete. See the end of this man page for details. Description The mcd command is used to change the mtools working directory on the MS-DOS disk. It uses the following syntax: mcd [msdosdirectory] Without arguments, mcd reports the current device and working directory. Otherwise, mcd changes the current device and current working directory relative to an MS-DOS filesystem. The environmental variable MCWD may be used to locate the file where the device and current working directory information is stored. The default is `$HOME/.mcwd'. Information in this file is ignored if the file is more than 6 hours old. Mcd returns 0 on success or 1 on failure. Unlike MS-DOS versions of CD, mcd can be used to change to another device. It may be wise to remove old `.mcwd' files at logout. See Also Mtools' texinfo doc Viewing the texi doc This manpage has been automatically generated from mtools's texinfo documentation. However, this process is only approximative, and some items, such as crossreferences, footnotes and indices are lost in this translation process. Indeed, these items have no appropriate repre- sentation in the manpage format. Moreover, not all information has been translated into the manpage version. Thus I strongly advise you to use the original texinfo doc. See the end of this manpage for instructions how to view the texinfo doc. * To generate a printable copy from the texinfo doc, run the following commands: ./configure; make dvi; dvips mtools.dvi * To generate a html copy, run: ./configure; make html A premade html can be found at: `http://mtools.linux.lu' and also at: `http://www.tux.org/pub/knaff/mtools' * To generate an info copy (browsable using emacs' info mode), run: ./configure; make info The texinfo doc looks most pretty when printed or as html. Indeed, in the info version certain examples are difficult to read due to the quoting conventions used in info. mtools-3.9.8 02Jun01 mcd(1)
Check Out this Related Man Page
mcd(1) General Commands Manual mcd(1) Name mcd - change MSDOS directory Note of warning This manpage has been automatically generated from mtools's texinfo documentation, and may not be entirely accurate or complete. See the end of this man page for details. Description The mcd command is used to change the mtools working directory on the MS-DOS disk. It uses the following syntax: mcd [msdosdirectory] Without arguments, mcd reports the current device and working directory. Otherwise, mcd changes the current device and current working directory relative to an MS-DOS file system. The environmental variable MCWD may be used to locate the file where the device and current working directory information is stored. The default is `$HOME/.mcwd'. Information in this file is ignored if the file is more than 6 hours old. Mcd returns 0 on success or 1 on failure. Unlike MS-DOS versions of CD, mcd can be used to change to another device. It may be wise to remove old `.mcwd' files at logout. See Also Mtools' texinfo doc Viewing the texi doc This manpage has been automatically generated from mtools's texinfo documentation. However, this process is only approximative, and some items, such as crossreferences, footnotes and indices are lost in this translation process. Indeed, these items have no appropriate repre- sentation in the manpage format. Moreover, not all information has been translated into the manpage version. Thus I strongly advise you to use the original texinfo doc. See the end of this manpage for instructions how to view the texinfo doc. * To generate a printable copy from the texinfo doc, run the following commands: ./configure; make dvi; dvips mtools.dvi * To generate a html copy, run: ./configure; make html A premade html can be found at `http://www.gnu.org/software/mtools/manual/mtools.html' * To generate an info copy (browsable using emacs' info mode), run: ./configure; make info The texinfo doc looks most pretty when printed or as html. Indeed, in the info version certain examples are difficult to read due to the quoting conventions used in info. mtools-4.0.13 28Feb10 mcd(1)