how can I get network services


 
Thread Tools Search this Thread
Operating Systems HP-UX how can I get network services
# 1  
Old 11-08-2008
how can I get network services

Hi

Is there a cmd in hpux 11 to get the network services

the network services must display "Listen" like command netstat -an |grep Listen and display the process that is running on a port in HP-Unix at the same time


my request can not use lsof -i command,not to install any extral software

only use basic hp ux command

can I do it!!



thank you
# 2  
Old 11-08-2008
# 3  
Old 11-08-2008
Is there any other way I can get it without installing any command i.e. lsof with existing commands on Version 11iv31

I want to find the process id (PID) of the process running on a particular port to find network services
Login or Register to Ask a Question

Previous Thread | Next Thread

8 More Discussions You Might Find Interesting

1. Debian

How do i correct restart network-services in Debian?

Hello, I would like to do follow steps. Set a static IP-Adress on eth0 (For Testing) Set DHCP on eth0 All steps should be done without a single reboot. /etc/network/interfaces iface eth0 inet static address 192.0.2.7/24 gateway 192.0.2.254How do i perform... (3 Replies)
Discussion started by: int3g3r
3 Replies

2. Shell Programming and Scripting

Monitor some of network services

Hi I want to write a script for netflow service because my service doesnt send any packet to netflow walker (server). Although the service is started but it does not send any packet to server until i restart the service I want to write a script in order to restart the service... (7 Replies)
Discussion started by: mohsen1366
7 Replies

3. Shell Programming and Scripting

Script to Start services based on dependent services on other AIX machine

Hi, I just started working on a script. After my research, i found a command which can help me: AIM: To build a script which starts the services (Services 1) on server 1 automatically whenever its down. And it has a dependency on other service (Service 2) on Server 2. So my script has to... (4 Replies)
Discussion started by: draghun9
4 Replies

4. Red Hat

Restart of services if port no is changed in /etc/services in RHEL

I had a doubt if any services need to be restarted if port no in /etc/services in an RHEL setup is changed. For eg, the port no of 443 for SSL may need to be changed. I hope my query is clear whether any services need to be restarted if port no in /etc/services is changed. Please revert with... (10 Replies)
Discussion started by: RHCE
10 Replies

5. IP Networking

Oracle network services

i have installd oracle 10 on Solaris 10 now i want to access this database from remote machine. -bash-3.00$ tnsping 192.168.92.49 TNS Ping Utility for Solaris: Version 10.2.0.2.0 - Production on 17-DEC-2010 21:06:51 Copyright (c) 1997, 2005, Oracle. All rights reserved. Used... (0 Replies)
Discussion started by: akhaliq22
0 Replies

6. UNIX for Dummies Questions & Answers

Search for network services

OK I am a complete newbie to Unix. We have a Sunfire V890 running SUNOS Release 5.9. The Operating Environment is Solaris 9. I have been tasked with determining whether or not specific network and solaris services are enabled or disabled. If the services are enabled I need to disable them. I'm... (12 Replies)
Discussion started by: coachgt1
12 Replies

7. IP Networking

stopping and starting network services

Solaris v5.6 how do you stop and start the network services? (4 Replies)
Discussion started by: Westy564
4 Replies

8. UNIX for Advanced & Expert Users

Long Delay if any with network services

While installing a firewall, I was pinging the interface from SCO 5.0.6 Openserver box, while no response, I hit "DEL" to cancel, but no cancel. Then all of a sudden I get BOO-KOO traffic lights on HUB and Switch.... Then a kernel trap error. System froze... Proceeded with a cold boot. Now I have... (8 Replies)
Discussion started by: nashvillek5
8 Replies
Login or Register to Ask a Question