PX(4) BSD Kernel Interfaces Manual PX(4)NAME
px -- driver for TURBOchannel PX accelerated graphics boards
SYNOPSIS
px* at tc? slot ? offset ?
wsdisplay* at px?
DESCRIPTION
The px driver provides support for the 2D DEC PixelStamp video display option card (PMAG-C).
SEE ALSO pxg(4), tc(4), wscons(4)HISTORY
The px driver first appeared in NetBSD 1.3. It became usable as a console device in NetBSD 1.5.
BUGS
NetBSD/pmax does not currently support the machine-independent wscons(4) interface and uses a machine-dependent driver.
BSD September 21, 2001 BSD
Check Out this Related Man Page
STGE(4) BSD Kernel Interfaces Manual STGE(4)NAME
stge -- Sundance/Tamarack TC9021 Gigabit Ethernet driver
SYNOPSIS
stge* at pci? dev ? function ?
Configuration of PHYs or Ten-bit interfaces may also be necessary. See mii(4).
DESCRIPTION
The stge device driver supports the Sundance/Tamarack TC9021 Gigabit Ethernet chip.
The Sundance/Tamarack TC9021 is found on the D-Link DGE-550T, and the Antares Microsystems Gigabit Ethernet board. It uses an external PHY
or an external 10-bit interface.
The TC9021 supports IPv4/TCP/UDP checksumming in hardware. The stge driver supports this feature of the chip. See ifconfig(8) for informa-
tion on how to enable this feature.
SEE ALSO arp(4), ifmedia(4), mii(4), netintro(4), pci(4), ifconfig(8)HISTORY
The stge driver first appeared in NetBSD 1.6.
AUTHORS
The stge driver was written by Jason R. Thorpe <thorpej@NetBSD.org>.
BUGS
The stge driver does not support the VLAN tag insertion/removal feature of the TC9021 chip. This is primarily because the TC9021's VLAN do
not have a useful programming interface.
The stge driver does not yet support jumbo Ethernet frames.
The stge driver does not yet function properly with 1000BASE-T fitted boards. Currently, only 1000BASE-SX boards work.
BSD July 24, 2001 BSD
Hi everybody I have a problem with wtmpx. Accounting file. I activated it. It works but to well :( Writes the same message every minute. "faxmodem" As you can see it does not take to long until my /var file is soon full.
Thanks
Peter (26 Replies)
Hi!
Is there any possibility to determine whether some Solaris machine has PXE enabled? I need some kind of a utility, which I could invoke remotely.
Thanks! (5 Replies)
Platform sol 8
I had wtmpx growing very large(1.2 G). I copied the file and compressed it the did a "cat /dev/null > /var/adm/wtmpx" to zero out the file and not close any doors to any processes. (After searching this seemed like the right method)
This is a box that gets accessed from other... (5 Replies)
Hi,
I am using Sun Solaris 5.9 OS. I have found a file called wtmpx having a size of 5.0 GB. I want to clear this file using :>/var/adm/wtmpx. My query is, would it cause any problem to the running live system.
Could anyone suggest the best method to clear the file without causing problem to... (6 Replies)
we have a v440 SUN machine with a NetApp FAS3140 SAN storage, the v440 got 2 HBA qlogic cards both connected to the switch side in NetApp 3140, zoning in netapp configured proberly and luns are adversitesed to the SUN machine, the problem i am facing is that when i try to configure the mpxio i am... (7 Replies)
Hi,
I am trying to setup a server for a diskless boot of a computer class (with ubuntu)
I followed the guidelines in https://help.ubuntu.com/community/DisklessUbuntuHowto
I have two computers: one is the server I installed and the other is my macbook on which I run a virtual machine... (8 Replies)
i have automated installation of my proprietory linux.. using PXE. it all goes well. but after complete installation, while using the admin interface.. i am facing display problems.
is it due to package dependencies.?
or i have to write post script in anaconda-ks.cfg file???
can some one tell... (10 Replies)
Hi all,
I have a problem with PXE Server.
I have finished to configure PXE Server with DHCP.
when I create a new Machine on my vSphere and turn it on the installation process takes more then 2 hours .
I have configured on my ESX Server new Switch that is dedicated for this installation... (8 Replies)
There is an aspx page which, when accessed with certain parameters in the URL, downloads a file. I need to do this with a shell script. I tried using wget, but I get a response of 302 from the server, which redirects me to the default page and then downloads the default page html itself. I... (6 Replies)
I have recently been assigned to help maintain some testing software on two UNIX stations. The stations are connected to instruments that supply power, signals, and take measurements from a box. Both test stations are basically the same. I was given a crash course (read a little training) a couple... (18 Replies)
I have been asked to modify our PXE server such that there will be only one entry in the pxelinux.cfg/default file, where the same kernel and initrd.img will be used regardless of what operating system is to be installed, and the user will type in the path to the kickstart file that will be used. ... (7 Replies)
Hi All
I work on solaris 8, 9 and 10 platforms and have encountered an error which is my wtmpx files appear to be corrupted as all entries contain the date 1970 (the birth of unix).
Now this is obviously not the case, so my query is:
1 - Can the existing wtmpx files be manipulated to... (6 Replies)
hi,
we have a solaris 10 box that was handled by a different sysadmin before & now it is turned over to us for system administration. our concern is that if we issue the "last" command, it usually says "wtmp begins current day current month date 02:30". just like this "wtmp begins Thu Mar 7... (6 Replies)