Linux and UNIX Man Pages

Linux & Unix Commands - Search Man Pages

NetBSD 6.1.5 - man page for rpc_soc (netbsd section 3)

RPC_SOC(3)				     BSD Library Functions Manual				   RPC_SOC(3)

NAME
rpc_soc, auth_destroy, authnone_create, authunix_create, authunix_create_default, callrpc, clnt_broadcast, clnt_call, clnt_control, clnt_create, clnt_destroy, clnt_freeres, clnt_geterr, clnt_pcreateerror, clnt_perrno, clnt_perror, clnt_spcreateerror, clnt_sperrno, clnt_sperror, clntraw_create, clnttcp_create, clntudp_bufcreate, clntudp_create, get_myaddress, pmap_getmaps, pmap_getport, pmap_rmtcall, pmap_set, pmap_unset, registerrpc, rpc_createerr, svc_destroy, svc_fds, svc_fdset, svc_getargs, svc_getcaller, svc_getreg, svc_getregset, svc_getrpccaller, svc_register, svc_run, svc_sendreply, svc_unregister, svcerr_auth, svcerr_decode, svcerr_noproc, svcerr_noprog, svcerr_progvers, svcerr_systemerr, svcerr_weakauth, svcfd_create, svcraw_create, xdr_accepted_reply, xdr_authunix_parms, xdr_callhdr, xdr_callmsg, xdr_opaque_auth, xdr_pmap, xdr_pmaplist, xdr_rejected_reply, xdr_replymsg, xprt_register, xprt_unregister -- library routines for remote procedure calls
SYNOPSIS
#include <rpc/rpc.h> void auth_destroy(AUTH *auth); AUTH * authnone_create(void); AUTH * authunix_create(char *host, int uid, int gid, int len, int *aup_gids); AUTH * authunix_create_default(void); int callrpc(char *host, u_long prognum, u_long versnum, u_long procnum, xdrproc_t inproc, char *in, xdrproc_t outproc, char *out); enum clnt_stat clnt_broadcast(u_long prognum, u_long versnum, u_long procnum, xdrproc_t inproc, char *in, xdrproc_t outproc, char *out, resultproc_t eachresult); enum clnt_stat clnt_call(CLIENT *clnt, u_long procnum, xdrproc_t inproc, char *in, xdrproc_t outproc, char *out, struct timeval tout); int clnt_destroy(CLIENT *clnt); CLIENT * clnt_create(char *host, u_long prog, u_long vers, char *proto); bool_t clnt_control(CLIENT *cl, u_int req, char *info); int clnt_freeres(CLIENT *clnt, xdrproc_t outproc, char *out); void clnt_geterr(CLIENT *clnt, struct rpc_err errp); void clnt_pcreateerror(char *s); void clnt_perrno(enum clnt_stat stat); int clnt_perror(CLIENT *clnt, char *s); char * clnt_spcreateerror(const char *s); char * clnt_sperrno(enum clnt_stat stat); char * clnt_sperror(CLIENT *rpch, char *s); CLIENT * clntraw_create(u_long prognum, u_long versnum); CLIENT * clnttcp_create(struct sockaddr_in *addr, u_long prognum, u_long versnum, int *sockp, u_int sendsz, u_int recvsz); CLIENT * clntudp_create(struct sockaddr_in *addr, u_long prognum, u_long versnum, struct timeval wait, int *sockp); CLIENT * clntudp_bufcreate(struct sockaddr_in *addr, u_long prognum, u_long versnum, struct timeval wait, int *sockp, unsigned int sendsize, unsigned int recosize); int get_myaddress(struct sockaddr_in *addr); struct pmaplist * pmap_getmaps(struct sockaddr_in *addr); u_short pmap_getport(struct sockaddr_in *addr, u_long prognum, u_long versnum, u_long protocol); enum clnt_stat pmap_rmtcall(struct sockaddr_in *addr, u_long prognum, u_long versnum, u_long procnum, xdrproc_t inproc, char *in, xdrpoc_t outproc, char *out, struct timeval tout, u_long *portp); int pmap_set(u_long prognum, u_long versnum, int protocol, int port); int pmap_unset(u_long prognum, u_long versnum); int registerrpc(u_long prognum, u_long versnum, u_long procnum, char *(*procname)(), xdrproc_t inproc, xdrproc_t outproc); struct rpc_createerr rpc_createerr; int svc_destroy(SVCXPRT *xprt); fd_set svc_fdset; int svc_fds; int svc_freeargs(SVCXPRT *xprt, xdrproc_t inproc, char *in); int svc_getargs(SVCXPRT *xprt, xdrproc_t inproc, char *in); struct sockaddr_in * svc_getcaller(SVCXPRT *xprt); int svc_getreqset(fd_set *rdfds); int svc_getreq(int rdfds); struct netbuf * svc_getrpccaller(SVCXPRT *xprt); int svc_register(SVCXPRT *xprt, u_long prognum, u_long versnum, void (*dispatch)(), u_long protocol); int svc_run(void); int svc_sendreply(SVCXPRT *xprt, xdrproc_t outproc, char *out); void svc_unregister(u_long prognum, u_long versnum); void svcerr_auth(SVCXPRT *xprt, enum auth_stat why); void svcerr_decode(SVCXPRT *xprt); void svcerr_noproc(SVCXPRT *xprt); void svcerr_noprog(SVCXPRT *xprt); void svcerr_progvers(SVCXPRT *xprt); void svcerr_systemerr(SVCXPRT *xprt); void svcerr_weakauth(SVCXPRT *xprt); SVCXPRT * svcraw_create(void); SVCXPRT * svctcp_create(int sock, u_int send_buf_size, u_int recv_buf_size); SVCXPRT * svcfd_create(int fd, u_int sendsize, u_int recvsize); SVCXPRT * svcudp_bufcreate(int sock, u_int sendsize, u_int recosize); SVCXPRT * svcudp_create(int sock); int xdr_accepted_reply(XDR *xdrs, struct accepted_reply *ar); int xdr_authunix_parms(XDR *xdrs, struct authunix_parms *aupp); void xdr_callhdr(XDR *xdrs, struct rpc_msg *chdr); int xdr_callmsg(XDR *xdrs, struct rpc_msg *cmsg); int xdr_opaque_auth(XDR *xdrs, struct opaque_auth *ap); int xdr_pmap(XDR *xdrs, struct pmap *regs); int xdr_pmaplist(XDR *xdrs, struct pmaplist **rp); int xdr_rejected_reply(XDR *xdrs, struct rejected_reply *rr); int xdr_replymsg(XDR *xdrs, struct rpc_msg *rmsg); void xprt_register(SVCXPRT *xprt); void xprt_unregister(SVCXPRT *xprt);
DESCRIPTION
The svc and clnt functions described in this page are the old, TS-RPC interface to the XDR and RPC library, and exist for backward compatibility. The new interface is described in the pages referenced from rpc(3). These routines allow C programs to make procedure calls on other machines across the network. First, the client calls a procedure to send a data packet to the server. Upon receipt of the packet, the server calls a dispatch routine to perform the requested service, and then sends back a reply. Finally, the procedure call returns to the client. auth_destroy() A macro that destroys the authentication information associated with auth. Destruction usually involves deallocation of private data structures. The use of auth is undefined after calling auth_destroy(). authnone_create() Create and returns an RPC authentication handle that passes nonusable authentication information with each remote procedure call. This is the default authentication used by RPC. authunix_create() Create and return an RPC authentication handle that contains authentication information. The parameter host is the name of the machine on which the information was created; uid is the user's user ID; gid is the user's current group id; len and aup_gids refer to a counted array of groups to which the user belongs. It is easy to impersonate a user. authunix_create_default() Calls authunix_create() with the appropriate parameters. callrpc() Call the remote procedure associated with prognum, versnum, and procnum on the machine, host. The parame- ter in is the address of the procedure's argument(s), and out is the address of where to place the result(s); inproc is used to encode the procedure's parameters, and outproc is used to decode the proce- dure's results. This routine returns zero if it succeeds, or the value of enum clnt_stat cast to an inte- ger if it fails. The routine clnt_perrno() is handy for translating failure statuses into messages. Warning: calling remote procedures with this routine uses UDP/IP as a transport; see clntudp_create() for restrictions. You do not have control of timeouts or authentication using this routine. clnt_broadcast() Like callrpc(), except the call message is broadcast to all locally connected broadcast nets. Each time it receives a response, this routine calls eachresult(), whose form is int eachresult(char *out, struct sockaddr_in *addr) where out is the same as out passed to clnt_broadcast(), except that the remote proce- dure's output is decoded there; addr points to the address of the machine that sent the results. If eachresult() returns zero, clnt_broadcast() waits for more replies; otherwise it returns with appropriate status. Warning: broadcast sockets are limited in size to the maximum transfer unit of the data link. For ether- net, this value is 1500 bytes. clnt_call() A macro that calls the remote procedure procnum associated with the client handle, clnt, which is obtained with an RPC client creation routine such as clnt_create(). The parameter in is the address of the proce- dure's argument(s), and out is the address of where to place the result(s); inproc is used to encode the procedure's parameters, and outproc is used to decode the procedure's results; tout is the time allowed for results to come back. clnt_destroy() A macro that destroys the client's RPC handle. Destruction usually involves deallocation of private data structures, including clnt itself. Use of clnt is undefined after calling clnt_destroy(). If the RPC library opened the associated socket, it will close it also. Otherwise, the socket remains open. clnt_create() Generic client creation routine. host identifies the name of the remote host where the server is located. proto indicates which kind of transport protocol to use. The currently supported values for this field are ``udp'' and ``tcp''. Default timeouts are set, but can be modified using clnt_control(). Warning: Using UDP has its shortcomings. Since UDP-based RPC messages can only hold up to 8 Kbytes of encoded data, this transport cannot be used for procedures that take large arguments or return huge results. clnt_control() A macro used to change or retrieve various information about a client object. req indicates the type of operation, and info is a pointer to the information. For both UDP and TCP the supported values of req and their argument types and what they do are: CLSET_TIMEOUT struct timeval; set total timeout. CLGET_TIMEOUT struct timeval; get total timeout. Note: if you set the timeout using clnt_control(), the timeout parameter passed to clnt_call() will be ignored in all future calls. CLGET_SERVER_ADDR struct sockaddr_in; get server's address. The following operations are valid for UDP only: CLSET_RETRY_TIMEOUT struct timeval; set the retry timeout. CLGET_RETRY_TIMEOUT struct timeval; get the retry timeout. The retry timeout is the time that UDP RPC waits for the server to reply before retransmitting the request. clnt_freeres() A macro that frees any data allocated by the RPC/XDR system when it decoded the results of an RPC call. The parameter out is the address of the results, and outproc is the XDR routine describing the results. This routine returns one if the results were successfully freed, and zero otherwise. clnt_geterr() A macro that copies the error structure out of the client handle to the structure at address errp. clnt_pcreateerror() Print a message to standard error indicating why a client RPC handle could not be created. The message is prepended with string s and a colon. A newline character is appended at the end of the message. Used when a clnt_create(), clntraw_create(), clnttcp_create(), or clntudp_create() call fails. clnt_perrno() Print a message to standard error corresponding to the condition indicated by stat. A newline character is appended at the end of the message. Used after callrpc(). clnt_perror() Print a message to standard error indicating why an RPC call failed; clnt is the handle used to do the call. The message is prepended with string s and a colon. A newline character is appended at the end of the message. Used after clnt_call(). clnt_spcreateerror() Like clnt_pcreateerror(), except that it returns a string instead of printing to the standard error. Bugs: returns pointer to static data that is overwritten on each call. clnt_sperrno() Take the same arguments as clnt_perrno(), but instead of sending a message to the standard error indicating why an RPC call failed, return a pointer to a string which contains the message. clnt_sperrno() is used instead of clnt_perrno() if the program does not have a standard error (as a program running as a server quite likely does not), or if the programmer does not want the message to be output with printf(3), or if a message format different than that supported by clnt_perrno() is to be used. Note: unlike clnt_sperror() and clnt_spcreateerror(), clnt_sperrno() returns a pointer to static data, but the result will not get overwritten on each call. clnt_sperror() Like clnt_perror(), except that (like clnt_sperrno()) it returns a string instead of printing to standard error. Bugs: returns pointer to static data that is overwritten on each call. clntraw_create() This routine creates a toy RPC client for the remote program prognum, version versnum. The transport used to pass messages to the service is actually a buffer within the process's address space, so the correspond- ing RPC server should live in the same address space; see svcraw_create(). This allows simulation of RPC and acquisition of RPC overheads, such as round trip times, without any kernel interference. This routine returns NULL if it fails. clnttcp_create() This routine creates an RPC client for the remote program prognum, version versnum; the client uses TCP/IP as a transport. The remote program is located at Internet address *addr. If addr->sin_port is zero, then it is set to the actual port that the remote program is listening on (the remote rpcbind(8) or portmap ser- vice is consulted for this information). The parameter sockp is a socket; if it is RPC_ANYSOCK, then this routine opens a new one and sets sockp. Since TCP-based RPC uses buffered I/O , the user may specify the size of the send and receive buffers with the parameters sendsz and recvsz; values of zero choose suitable defaults. This routine returns NULL if it fails. clntudp_create() This routine creates an RPC client for the remote program prognum, version versnum; the client uses UDP/IP as a transport. The remote program is located at Internet address addr. If addr->sin_port is zero, then it is set to actual port that the remote program is listening on (the remote rpcbind(8) or portmap service is consulted for this information). The parameter sockp is a socket; if it is RPC_ANYSOCK, then this rou- tine opens a new one and sets sockp. The UDP transport resends the call message in intervals of wait time until a response is received or until the call times out. The total time for the call to time out is spec- ified by clnt_call. Warning: since UDP-based RPC messages can only hold up to 8 Kbytes of encoded data, this transport cannot be used for procedures that take large arguments or return huge results. clntudp_bufcreate() This routine creates an RPC client for the remote program prognum, on versnum; the client uses UDP/IP as a transport. The remote program is located at Internet address addr. If addr->sin_port is zero, then it is set to actual port that the remote program is listening on (the remote rpcbind(8) or portmap service is consulted for this information). The parameter sockp is a socket; if it is RPC_ANYSOCK, then this routine opens a new one and sets sockp. The UDP transport resends the call message in intervals of wait time until a response is received or until the call times out. The total time for the call to time out is specified by clnt_call. This allows the user to specify the maximum packet size for sending and receiving UDP-based RPC messages. get_myaddress() Stuff the machine's IP address into *addr, without consulting the library routines that deal with /etc/hosts. The port number is always set to htons(PMAPPORT). Returns zero on success, non-zero on fail- ure. pmap_getmaps() A user interface to the rpcbind(8) service, which returns a list of the current RPC program-to-port map- pings on the host located at IP address *addr. This routine can return NULL. The command rpcinfo -p uses this routine. pmap_getport() A user interface to the rpcbind(8) service, which returns the port number on which waits a service that supports program number prognum, version versnum, and speaks the transport protocol associated with protocol. The value of protocol is most likely IPPROTO_UDP or IPPROTO_TCP. A return value of zero means that the mapping does not exist or that the RPC system failured to contact the remote rpcbind(8) service. In the latter case, the global variable rpc_createerr() contains the RPC status. pmap_rmtcall() A user interface to the rpcbind(8) service, which instructs rpcbind(8) on the host at IP address *addr to make an RPC call on your behalf to a procedure on that host. The parameter *portp will be modified to the program's port number if the procedure succeeds. The definitions of other parameters are discussed in callrpc() and clnt_call(). This procedure should be used for a ``ping'' and nothing else. See also clnt_broadcast(). pmap_set() A user interface to the rpcbind(8) service, which establishes a mapping between the triple [prognum, versnum, protocol] and port on the machine's rpcbind(8) service. The value of protocol is most likely IPPROTO_UDP or IPPROTO_TCP. This routine returns one if it succeeds, zero otherwise. Automatically done by svc_register(). pmap_unset() A user interface to the rpcbind(8) service, which destroys all mapping between the triple [prognum, versnum, *] and ports on the machine's rpcbind(8) service. This routine returns one if it succeeds, zero otherwise. registerrpc() Register procedure procname with the RPC service package. If a request arrives for program prognum, ver- sion versnum, and procedure procnum, procname is called with a pointer to its parameter(s); progname should return a pointer to its static result(s); inproc is used to decode the parameters while outproc is used to encode the results. This routine returns zero if the registration succeeded, -1 otherwise. Warning: remote procedures registered in this form are accessed using the UDP/IP transport; see svcudp_bufcreate() for restrictions. struct rpc_createerr rpc_createerr; A global variable whose value is set by any RPC client creation routine that does not succeed. Use the routine clnt_pcreateerror() to print the reason why. svc_destroy() A macro that destroys the RPC service transport handle, xprt. Destruction usually involves deallocation of private data structures, including xprt itself. Use of xprt is undefined after calling this routine. fd_set svc_fdset; A global variable reflecting the RPC service side's read file descriptor bit mask; it is suitable as a parameter to the select(2) system call. This is only of interest if a service implementor does not call svc_run(), but rather does his own asynchronous event processing. This variable is read-only (do not pass its address to select(2)!), yet it may change after calls to svc_getreqset() or any creation routines. int svc_fds; Similar to svc_fedset(), but limited to 32 descriptors. This interface is obsoleted by svc_fdset(). svc_freeargs() A macro that frees any data allocated by the RPC/XDR system when it decoded the arguments to a service pro- cedure using svc_getargs(). This routine returns 1 if the results were successfully freed, and zero other- wise. svc_getargs() A macro that decodes the arguments of an RPC request associated with the RPC service transport handle, xprt. The parameter in is the address where the arguments will be placed; inproc is the XDR routine used to decode the arguments. This routine returns one if decoding succeeds, and zero otherwise. svc_getcaller() The obsolete way of getting the network address of the caller of a procedure associated with the RPC ser- vice transport handle, xprt, use svc_getrpccaller(). svc_getreqset() This routine is only of interest if a service implementor does not call svc_run(), but instead implements custom asynchronous event processing. It is called when the select(2) system call has determined that an RPC request has arrived on some RPC socket(s) ; rdfds is the resultant read file descriptor bit mask. The routine returns when all sockets associated with the value of rdfds have been serviced. svc_getreq() Similar to svc_getreqset(), but limited to 32 descriptors. This interface is obsoleted by svc_getreqset(). svc_getrpccaller() The approved way of getting the network address of the caller of a procedure associated with the RPC ser- vice transport handle, xprt. svc_register() Associates prognum and versnum with the service dispatch procedure, dispatch. If protocol is zero, the service is not registered with the rpcbind(8) service. If protocol is non-zero, then a mapping of the triple [prognum, versnum, protocol] to xprt->xp_port is established with the local rpcbind(8) service (gen- erally protocol is zero, IPPROTO_UDP or IPPROTO_TCP). The procedure dispatch has the following form: int dispatch(struct svc_req *request, SVCXPRT *xprt). The svc_register() routine returns one if it succeeds, and zero otherwise. svc_run() This routine never returns. It waits for RPC requests to arrive, and calls the appropriate service proce- dure using svc_getreq() when one arrives. This procedure is usually waiting for a select(2) system call to return. svc_sendreply() Called by an RPC service's dispatch routine to send the results of a remote procedure call. The parameter xprt is the request's associated transport handle; outproc is the XDR routine which is used to encode the results; and out is the address of the results. This routine returns one if it succeeds, zero otherwise. svc_unregister() Remove all mapping of the double [prognum, versnum] to dispatch routines, and of the triple [prognum, versnum, *] to port number. svcerr_auth() Called by a service dispatch routine that refuses to perform a remote procedure call due to an authentica- tion error. svcerr_decode() Called by a service dispatch routine that cannot successfully decode its parameters. See also svc_getargs(). svcerr_noproc() Called by a service dispatch routine that does not implement the procedure number that the caller requests. svcerr_noprog() Called when the desired program is not registered with the RPC package. Service implementors usually do not need this routine. svcerr_progvers() Called when the desired version of a program is not registered with the RPC package. Service implementors usually do not need this routine. svcerr_systemerr() Called by a service dispatch routine when it detects a system error not covered by any particular protocol. For example, if a service can no longer allocate storage, it may call this routine. svcerr_weakauth() Called by a service dispatch routine that refuses to perform a remote procedure call due to insufficient authentication parameters. The routine calls svcerr_auth(xprt, AUTH_TOOWEAK). svcraw_create() This routine creates a toy RPC service transport, to which it returns a pointer. The transport is really a buffer within the process's address space, so the corresponding RPC client should live in the same address space; see clntraw_create(). This routine allows simulation of RPC and acquisition of RPC overheads (such as round trip times), without any kernel interference. This routine returns NULL if it fails. svctcp_create() This routine creates a TCP/IP-based RPC service transport, to which it returns a pointer. The transport is associated with the socket sock, which may be RPC_ANYSOCK, in which case a new socket is created. If the socket is not bound to a local TCP port, then this routine binds it to an arbitrary port. Upon completion, xprt->xp_sock is the transport's socket descriptor, and xprt->xp_port is the transport's port number. This routine returns NULL if it fails. Since TCP-based RPC uses buffered I/O , users may specify the size of buffers; values of zero choose suitable defaults. svcfd_create() Create a service on top of any open descriptor. Typically, this descriptor is a connected socket for a stream protocol such as TCP. sendsize and recvsize indicate sizes for the send and receive buffers. If they are zero, a reasonable default is chosen. svcudp_bufcreate() This routine creates a UDP/IP-based RPC service transport, to which it returns a pointer. The transport is associated with the socket sock, which may be RPC_ANYSOCK, in which case a new socket is created. If the socket is not bound to a local UDP port, then this routine binds it to an arbitrary port. Upon completion, xprt->xp_sock is the transport's socket descriptor, and xprt->xp_port is the transport's port number. This routine returns NULL if it fails. This allows the user to specify the maximum packet size for sending and receiving UDP-based RPC messages. svcudp_create() This acts as svcudp_bufcreate(with) predefined sizes for the maximum packet sizes. xdr_accepted_reply() Used for encoding RPC reply messages. This routine is useful for users who wish to generate RPC-style mes- sages without using the RPC package. xdr_authunix_parms() Used for describing UNIX credentials. This routine is useful for users who wish to generate these creden- tials without using the RPC authentication package. xdr_callhdr() Used for describing RPC call header messages. This routine is useful for users who wish to generate RPC- style messages without using the RPC package. xdr_callmsg() Used for describing RPC call messages. This routine is useful for users who wish to generate RPC-style messages without using the RPC package. xdr_opaque_auth() Used for describing RPC authentication information messages. This routine is useful for users who wish to generate RPC-style messages without using the RPC package. xdr_pmap() Used for describing parameters to various rpcbind(8) procedures, externally. This routine is useful for users who wish to generate these parameters without using the pmap interface. xdr_pmaplist() Used for describing a list of port mappings, externally. This routine is useful for users who wish to gen- erate these parameters without using the pmap interface. xdr_rejected_reply() Used for describing RPC reply messages. This routine is useful for users who wish to generate RPC-style messages without using the RPC package. xdr_replymsg() Used for describing RPC reply messages. This routine is useful for users who wish to generate RPC-style messages without using the RPC package. xprt_register() After RPC service transport handles are created, they should register themselves with the RPC service pack- age. This routine modifies the global variable svc_fds. Service implementors usually do not need this routine. xprt_unregister() Before an RPC service transport handle is destroyed, it should unregister itself with the RPC service pack- age. This routine modifies the global variable svc_fds. Service implementors usually do not need this routine.
SEE ALSO
xdr(3) The following manuals: Remote Procedure Calls: Protocol Specification. Remote Procedure Call Programming Guide. rpcgen Programming Guide. Sun Microsystems, Inc., USC-ISI, "RPC: Remote Procedure Call Protocol Specification", RFC, 1050.
BSD
December 12, 2008 BSD
All times are GMT -4. The time now is 08:16 AM.

Unix & Linux Forums Content Copyright 1993-2018. All Rights Reserved.
UNIX.COM Login
Username:
Password:  
Show Password





Not a Forum Member?
Forgot Password?