zfsboot(8) [freebsd man page]

ZFSBOOT(8)						    BSD System Manager's Manual 						ZFSBOOT(8)

NAME

     zfsboot -- bootcode for ZFS on BIOS-based computers

DESCRIPTION

     zfsboot is used on BIOS-based computers to boot from a filesystem in a ZFS pool.  zfsboot is installed in two parts on a disk or a partition
     used by a ZFS pool.  The first part, a single-sector starter boot block, is installed at the beginning of the disk or partition.  The second
     part, a main boot block, is installed at a special offset within the disk or partition.  Both areas are reserved by the ZFS on-disk specifi-
     cation for boot use.  If zfsboot is installed in a partition, then that partition should be made bootable using appropriate configuration and
     boot blocks described in boot(8).

BOOTING

     The zfsboot boot process is very similar to that of gptzfsboot(8).  One significant difference is that zfsboot does not currently support the
     GPT partitioning scheme.  Thus only whole disks and MBR partitions, traditionally referred to as slices, are probed for ZFS disk labels.  See
     the BUGS section in gptzfsboot(8) for some limitations of the MBR scheme support.

USAGE

     zfsboot supports all the same prompt and configuration file arguments as gptzfsboot(8).

FILES

     /boot/zfsboot  boot code binary
     /boot.config   parameters for the boot block (optional)
     /boot/config   alternative parameters for the boot block (optional)

EXAMPLES

     zfsboot is typically installed using dd(1).  To install zfsboot on the ada0 drive:

	   dd if=/boot/zfsboot of=/dev/ada0 count=1
	   dd if=/boot/zfsboot of=/dev/ada0 iseek=1 oseek=1024

     If the drive is currently in use, the GEOM safety will prevent writes and must be disabled before running the above commands:

	   sysctl kern.geom.debugflags=0x10

     zfsboot can also be installed in an MBR slice:

	   gpart create -s mbr ada0
	   gpart add -t freebsd ada0
	   gpart create -s BSD ada0s1
	   gpart bootcode -b /boot/boot0 ada0
	   gpart set -a active -i 1 ada0
	   dd if=/boot/zfsboot of=/dev/ada0s1 count=1
	   dd if=/boot/zfsboot of=/dev/ada0s1 iseek=1 oseek=1024

     Note that commands to create and populate a pool are not shown in the example above.

SEE ALSO

     dd(1), boot.config(5), boot(8), gptzfsboot(8), loader(8), zfsloader(8), zpool(8)

HISTORY

     zfsboot appeared in FreeBSD 7.3.

AUTHORS

     This manual page was written by Andriy Gapon <avg@FreeBSD.org>.

BUGS

     Installing zfsboot with dd(1) is a hack.  ZFS needs a command to properly install zfsboot onto a ZFS-controlled disk or partition.

BSD
								September 15, 2014							       BSD

GPTZFSBOOT(8)						    BSD System Manager's Manual 					     GPTZFSBOOT(8)

NAME

     gptzfsboot -- GPT bootcode for ZFS on BIOS-based computers

DESCRIPTION

     gptzfsboot is used on BIOS-based computers to boot from a filesystem in a ZFS pool.  gptzfsboot is installed in a freebsd-boot partition of a
     GPT-partitioned disk with gpart(8).

IMPLEMENTATION NOTES

     The GPT standard allows a variable number of partitions, but gptzfsboot only boots from tables with 128 partitions or less.

BOOTING

     gptzfsboot tries to find all ZFS pools that are composed of BIOS-visible hard disks or partitions on them.  gptzfsboot looks for ZFS device
     labels on all visible disks and in discovered supported partitions for all supported partition scheme types.  The search starts with the disk
     from which gptzfsboot itself was loaded.  Other disks are probed in BIOS defined order.  After a disk is probed and gptzfsboot determines
     that the whole disk is not a ZFS pool member, the individual partitions are probed in their partition table order.  Currently GPT and MBR
     partition schemes are supported.  With the GPT scheme, only partitions of type freebsd-zfs are probed.  The first pool seen during probing is
     used as a default boot pool.

     The filesystem specified by the bootfs property of the pool is used as a default boot filesystem.	If the bootfs property is not set, then
     the root filesystem of the pool is used as the default.  zfsloader(8) is loaded from the boot filesystem.	If /boot.config or /boot/config is
     present in the boot filesystem, boot options are read from it in the same way as boot(8).

     The ZFS GUIDs of the first successfully probed device and the first detected pool are made available to zfsloader(8) in the
     vfs.zfs.boot.primary_vdev and vfs.zfs.boot.primary_pool variables.

USAGE

     Normally gptzfsboot will boot in fully automatic mode.  However, like boot(8), it is possible to interrupt the automatic boot process and
     interact with gptzfsboot through a prompt.  gptzfsboot accepts all the options that boot(8) supports.

     The filesystem specification and the path to zfsloader(8) are different from boot(8).  The format is

     [zfs:pool/filesystem:][/path/to/loader]

     Both the filesystem and the path can be specified.  If only a path is specified, then the default filesystem is used.  If only a pool and
     filesystem are specified, then /boot/zfsloader is used as a path.

     Additionally, the status command can be used to query information about discovered pools.	The output format is similar to that of zpool
     status (see zpool(8)).

     The configured or automatically determined ZFS boot filesystem is stored in the zfsloader(8) loaddev variable, and also set as the initial
     value of the currdev variable.

FILES

     /boot/gptzfsboot  boot code binary
     /boot.config      parameters for the boot block (optional)
     /boot/config      alternative parameters for the boot block (optional)

EXAMPLES

     gptzfsboot is typically installed in combination with a ``protective MBR'' (see gpart(8)).  To install gptzfsboot on the ada0 drive:

	   gpart bootcode -b /boot/pmbr -p /boot/gptzfsboot -i 1 ada0

     gptzfsboot can also be installed without the PMBR:

	   gpart bootcode -p /boot/gptzfsboot -i 1 ada0

SEE ALSO

     boot.config(5), boot(8), gpart(8), loader(8), zfsloader(8), zpool(8)

HISTORY

     gptzfsboot appeared in FreeBSD 7.3.

AUTHORS

     This manual page was written by Andriy Gapon <avg@FreeBSD.org>.

BUGS

     gptzfsboot looks for ZFS meta-data only in MBR partitions (known on FreeBSD as slices).  It does not look into BSD disklabel(8) partitions
     that are traditionally called partitions.	If a disklabel partition happens to be placed so that ZFS meta-data can be found at the fixed off-
     sets relative to a slice, then gptzfsboot will recognize the partition as a part of a ZFS pool, but this is not guaranteed to happen.

BSD
								September 15, 2014							       BSD