twa(4) [freebsd man page]

TWA(4)							   BSD Kernel Interfaces Manual 						    TWA(4)

NAME

     twa -- 3ware 9000/9500/9550/9650 series SATA RAID controllers driver

SYNOPSIS

     To compile this driver into the kernel, place the following lines in your kernel configuration file:

	   device scbus
	   device twa

     Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):

	   twa_load="YES"

DESCRIPTION

     The twa driver provides support for AMCC's 3ware 9000/9500/9550/9650 series SATA controllers.

     These controllers are available in 4, 8, 12 or 16-port configurations, and support the following RAID levels: 0, 1, 10, 5, 50.  The device
     nodes for the controllers are of the form /dev/twaX, where X is the controller number.  The driver is implemented as a SCSI SIM under CAM,
     and, as such, the logical units that it controls are accessible via the device nodes, /dev/daY, where Y is the logical unit number.

HARDWARE

     The twa driver supports the following SATA RAID controllers:

     o	 AMCC's 3ware 9500S-4LP
     o	 AMCC's 3ware 9500S-8
     o	 AMCC's 3ware 9500S-8MI
     o	 AMCC's 3ware 9500S-12
     o	 AMCC's 3ware 9500S-12MI
     o	 AMCC's 3ware 9500SX-4LP
     o	 AMCC's 3ware 9500SX-8LP
     o	 AMCC's 3ware 9500SX-12
     o	 AMCC's 3ware 9500SX-12MI
     o	 AMCC's 3ware 9500SX-16ML
     o	 AMCC's 3ware 9550SX-4LP
     o	 AMCC's 3ware 9550SX-8LP
     o	 AMCC's 3ware 9550SX-12
     o	 AMCC's 3ware 9550SX-12MI
     o	 AMCC's 3ware 9550SX-16ML
     o	 AMCC's 3ware 9650SE-2LP
     o	 AMCC's 3ware 9650SE-4LPML
     o	 AMCC's 3ware 9650SE-8LPML
     o	 AMCC's 3ware 9650SE-12ML
     o	 AMCC's 3ware 9650SE-16ML
     o	 AMCC's 3ware 9650SE-24M8

DIAGNOSTICS

     Whenever the driver encounters a command failure, it prints out an error code in the format: "ERROR: (<error source>: <error code>):", fol-
     lowed by a text description of the error.	There are other error messages and warnings that the driver prints out, depending on the kinds of
     errors that it encounters.  If the driver is compiled with TWA_DEBUG defined, it prints out a whole bunch of debug messages, the quantity of
     which varies depending on the value assigned to TWA_DEBUG (0 to 10).

AUTHORS

     The twa driver and manpage were written by Vinod Kashyap <vkashyap@FreeBSD.org>.

BSD
								    May 9, 2007 							       BSD

Check Out this Related Man Page

HPTRR(4)						   BSD Kernel Interfaces Manual 						  HPTRR(4)

NAME

     hptrr -- HighPoint RocketRAID device driver

SYNOPSIS

     To compile this driver into the kernel, place the following line in your kernel configuration file:

	   device hptrr
	   device scbus
	   device da

     Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):

	   hptrr_load="YES"

     The following tunables are settable from the loader:

     hw.hptrr.attach_generic
     set to 1 to permit driver attach to chips with generic Marvell (non-HighPoint) PCI identification. These chips are also supported by ata(4)
     and mvs(4).  Some vendors are using same chips, but without providing RAID BIOS.

DESCRIPTION

     The hptrr driver provides support for HighPoint's RocketRAID based RAID controllers.

     These devices support SATA/ATA disk drives and provide RAID0 (striping), RAID1 (mirroring), and RAID5 functionality.

HARDWARE

     The hptrr driver supports the following RAID controllers:

     o	 RocketRAID 172x series
     o	 RocketRAID 174x series
     o	 RocketRAID 2210
     o	 RocketRAID 222x series
     o	 RocketRAID 2240
     o	 RocketRAID 230x series
     o	 RocketRAID 231x series
     o	 RocketRAID 232x series
     o	 RocketRAID 2340
     o	 RocketRAID 2522

NOTES

     The hptrr driver only works on the i386 and amd64 platforms as it requires a binary blob object from the manufacturer which they only supply
     for these platforms.  The hptrr driver does not work on i386 with pae(4) enabled.

     This driver does not support the RR182x series controller.  See the hptmv(4) manual page for details on support.

     This driver supersedes the older rr232x driver.

SEE ALSO

     ata(4), cam(4), hptmv(4), mvs(4), loader(8)

HISTORY

     The hptrr device driver first appeared in FreeBSD 6.3.

AUTHORS

     The hptrr device driver was written by HighPoint Technologies, Inc., and ported to FreeBSD by Scott Long.	This manual page was written by
     David E. O'Brien.

BUGS

     The hptrr driver does not support manipulating the RAID from the OS, RAIDs need to be set up from the on-board BIOS.

BSD
								   June 6, 2012 							       BSD

Linux and UNIX Man Pages

twa(4) [freebsd man page]

Check Out this Related Man Page